Which Way Do the Washers Install On the Curt Hitch C12228

Question

Question:

I noticed the washers that came with the hitch are convex conical tooth. Does it matter which way they are used? The directions dont mention it.

asked by: Jeff

0

Expert Reply:

The Curt Trailer Hitch Receiver part # C12228 comes with conical tooth washers which will install with the teeth facing the hitch.

expert reply by: Conner L

0

Answer 1

The recommended solution for installing a hitch where the bolts all don't seem to perfectly line up is to first start each install bolt and leave it as loose as possible. This gives you a bit more leeway to compensate for holes that don't…

view full answer...

Answer 2

We don't have a combo of the Curt Hitch Ball #C40008 and Curt Ball Mount #C45340. The ball mount is extremely heavy-duty, rated up to 17,000 pounds. I think it's safe to assume you don't have a torque wrench rated up to 450 foot pounds…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 6

Hey Adrian! The higher capacity for the B&W #BW47BR and Curt #C77MJ comes from the construction. The B&W hitch weighs 45 lbs and then the Curt and Trailer Mate #TMT54FR both weigh 32 lbs. The Trailer Mate does sit just a tad higher compared…

view full answer...

Answer 7

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 8

Hi Stephanie! Great question and you’re totally right to ask, because most hitches for the 2024 RAV4 do require a bit of bumper trimming. That includes the Oris Detachable Hitch #TS66VR, since it uses a hidden design that needs a hole cut in the…

view full answer...

Answer 9

Hey Tanner! These hitches are all pretty similar so it can be hard to decide between them. If I were you I would choose the Curt #C77MJ over the other two. The Curt #C77MJ and etrailer #e84ZV actually share the same design, and both have the…

view full answer...

Answer 10

Hey Justin! Based on the pin weight and GVWR of your 2020 Vanleigh Beacon 34RLB you will want to get the 4.5k TW model. There are two different models depending on your bolt pattern. If you have a Lippert 1621, 1621HD, 0719, or Fabex PB 600 Series…

view full answer...

Answer 11

There is not a recommended psi level when using Firestone Ride-Rite Air Helper Springs #F2709 with the exception the minimum 5 psi and maximum 150psi. It sounds like 70 psi gets you to level, which is ideal for towing. If 100 psi is more comfortable,…

view full answer...

Answer 12

Hey Jake, thanks for reaching out! You'll actually want to keep the OEM hitch on your 2005 GMC Sierra 2500 to install some TorkLift tie-downs as there aren't any TorkLift tie-downs that fit with the SuperHitch Original #TLC1204. For your OEM…

view full answer...

Which Way Do the Washers Install On the Curt Hitch C12228

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching