Brake Controller Wiring Harness to Install Redarc Tow-Pro Brake Controller on 2020 Jeep Gladiator

Question

Question:

Will this be compatible a 2020 gladiator rubicon with tow package?

asked by: Armando C

0

Expert Reply:

The # RED67FR brake controller wiring harness is compatible with both the # RED44FR Tow-Pro Elite and the # RED24FR Tow-Pro Liberty brake controllers, but the it's not compatible with the Jeep Gladiator. The good news is that we do offer a harness arrangement that would allow either controller to install on your Gladiator.

You'll need both the # 3073-P and the # 331-TPH-017 adapter if you go with the Tow-Pro Elite or if you decide that the lower-cost proportional # RED24FR Liberty model would work better for you, you'll need the # 3073-P harness and the # RED69FR pigtail. To install the Liberty, you'd cut off the black connector on the # 3073-P harness and wire it color for color with the # RED69FR pigtail. The installation of the Tow-Pro Elite would be completely plug and play.

The connector under the dash is located to the left of the steering column near the top of the e-brake pedal.

I'll link to an installation video that you might find helpful.

expert reply by: Mike L

0

Brake Controller Connector Location 2020 Jeep Gladiator
(click to enlarge)

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 4

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 7

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 10

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 11

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 12

Hey Omar, the removable arms of the base plate kits we offer are not able to be reused on a new vehicle as they are all designed very specifically to fit the exact base plate they were made for. There are fit variations between them even on exact…

view full answer...

Brake Controller Wiring Harness to Install Redarc Tow-Pro Brake Controller on 2020 Jeep Gladiator

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching