What Size Bolts To Install Replacement I-Beam Jack Bracket for Lippert Ground Control 3.0

Question

Question:

What size of the self tapping bolt to mount the bracket to the I beam

asked by: Tommy

1

Helpful Expert Reply:

I reached out to my contact at Lippert and he mentioned that the Replacement I-Beam Jack Bracket for Lippert Ground Control 3.0 # LC349975 has holes that are 0.57" diameter and designed for use with 1/2" diameter bolts.

expert reply by: Erik B

1

Answer 1

The overall height of the mounting plate of the Replacement I-Beam Jack Bracket for Lippert Ground Control #LC349975 is 13 inches.

view full answer...

Answer 2

I went ahead and pulled this Replacement I-Beam Jack Bracket #LC349975 from our warehouse to measure. I have attached the dimensions below. Hope this Helps.

view full answer...

Answer 3

I did a little digging on your 2021 Grand Design Reflection 303RLS, and it appears you have the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad and Remote #LC358590. With that being said, you'll want to use the…

view full answer...

Answer 4

Hi Jay, For just the front legs of the Lippert Ground Control 3.0 Leveling Systems you'll need part #LC305340. This comes with the leg, footplate, and motor.

view full answer...

Answer 5

We do not have those parts available. I checked the parts list for the Ground Control 3.0 Electric Leveling System #LC358590 (4-Point Set) or #LC675817 (6-Point Set) and the inner tube parts are not available by themselves. If you need a replacement…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Hey Matt! The Hellwig Load Pro 35 Heavy Duty Helper Springs #HE93XR are only designed to give you additional support while towing/hauling. Aftermarket suspension enhancement cannot increase the capacity of your 2024 Silverado 2500. The only way to…

view full answer...

Answer 10

Hey Jonathan. If you're wanting to have an airbag set up alone with a 5th wheel hitch, you will want to get a FIrestone kit. The Airlift kit you asked about, part #AL88341, will not be able to be installed along side a 5th wheel, or gooseneck, as…

view full answer...

Answer 11

Hi John, you’re definitely looking in the right place and I can help clear this up so you’re not guessing. For your 2021 Rogue Armored 351 G2, the correct MORryde X-Factor crossmember is the standard version part #MR33WR, and in most cases you will…

view full answer...

Answer 12

Hey Randy! I can definitely set you up with air bags and a compressor. I recommend Firestone since they make the most durable and reliable air bags. For a complete kit with an air compressor you can choose from the following: -Firestone Ride-Rite Air…

view full answer...

What Size Bolts To Install Replacement I-Beam Jack Bracket for Lippert Ground Control 3.0

Product Page this Question was Asked From

Continue Researching