Recommended Roof Vent Cover for a Ventline V3092-603-00

Question

Question:

Looking for recommendations for covers for our camper roof vents so we can leave our vents open - Ventline E-Z Lift Ventadome Trailer Roof Vent - Manual Lift and fan model in the bathroom - 14-1/4inch x 14-1/4inch - Smoke. Will the Camco roof vent cover work?

asked by: Luke A

0

Expert Reply:

The Camco RV and Enclosed Trailer Roof Vent Cover w/ Detachable Louvered Screen # CAM40431 will fit a Ventline E-Z Lift Ventadome Trailer Roof Vent # V3092-603-00. I do have to mention that the # V3092-603-00 will be 9 1/2 tall, and the # CAM40431 is also 9 1/2 inches tall, so there will be some contact when opened all the way. However, this will not affect or damage either product.

expert reply by: Lazer S

0

Answer 1

You would need the standard MaxxAir Vent Cover part #MA00-933069 as a vent cover for the top of the Ventline E-Z Lift Ventadome #V3092-603-00. This cove allows you to leave the vent open even if there's rain and not worry about water getting in.

view full answer...

Answer 2

Your travel trailer likely has a regulator with an automatic change over valve built into it. As you probably know, when the first bottle is empty it switches over to the second bottle. The bottle and switch are before the regulator, so only the one…

view full answer...

Answer 3

I spoke with my contact at MaxxAir regarding the MaxxAir 2 Vent Covers like the Smoke #MA00-933073 that you were looking at and the Standard Covers like #MA00-933067. He said there are two primary differences between the two models. The first is that…

view full answer...

Answer 4

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 5

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Thanks for the picture! I checked with Progressive Dynamics the replacement power converter you need for your Parallax Series 7300 Model 7345 is the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers - 45 Amp item #PD4645V.

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 10

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 11

The MaxxAir FanMate vent cover Item #MA00-955001 is going to be just a little taller but the louvred end tapers in and it does not come with the screen which is Item #MA00-955202. 25" long x 18-1/8" wide x 10-1/4" tall. The MaxxAir II…

view full answer...

Recommended Roof Vent Cover for a Ventline V3092-603-00

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching