Install Procedure for EcoHitch 306-X7235 Hitch on 2013 Honda Civic
Updated 06/18/2021 | Published 06/17/2021
Question:
I have a 2013 Honda Civic simple sedan. Im considering purchasing the Echohitch part # 306-X7235, and Im wondering if I can get a look at the instructions since you dont have a video covering how this hitch is installed?
asked by: Eric W
Expert Reply:
EcoHitch doesn't allow us to directly link their instructions, but I'd be happy to give you a synopsis of the procedure and send you a copy of the installation instructions in a separate email.
You'll begin by removing the clips on the underside of the fascia that hold the center trim panel and removing the panel. You'll also remove the underbody panel if the vehicle is so equipped. Then, you will temporarily lower the exhaust as demonstrated in the linked video. You'll want to use a ratchet strap to prevent the exhaust from falling too far.
You'll next remove the heat shield, then fish the hardware into the frame on both the passenger and driver side. I'll link a video showing how to do this. You'll then trim and reinstall the heat shield.
Next, raise the hitch into position being careful not to push the hardware up into the frame, and then secure the hardware. Having another pair of hands would be helpful here.
Finally, you'll trim the trim panel and the underbody panel and reinstall them.
After looking over the installation instructions, the install doesn't appear to be too difficult. A fairly handy do-it-yourselfer could complete the install in roughly 1-2 hours.
Product Page this Question was Asked From
EcoHitch Hidden Trailer Hitch Receiver - Custom Fit - 2"
- Trailer Hitch
- For Towing
- Class II
- 300 lbs TW
- 2000 lbs GTW
- 2 Inch Hitch
- Concealed Cross Tube
- EcoHitch
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: EcoHitch Hidden Trailer Hitch Receiver - Custom Fit - 2"
- Video: 2015 Honda Civic EcoHitch Hidden Trailer Hitch Receiver: Complete Installation
- Shop: etrailer Ball Mount w/ Pre-Torqued 2" Ball - 1-1/4" Hitch - 3-7/8" Rise - 3,500 lbs
- Shop: Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Trailer Wiring Diagrams
- Shop: Trailer Wiring
- Search Results: trailer hitch
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Search Results: trailer wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Q&A: Comparing the Curt Hitch C13416 and EcoHitch Hitch 306-X7396 for a 2019 Toyota RAV4
- Video: How to Choose a Trailer Brake Controller
- Search Results: trailer tires and wheels
- Article: How to Choose the Right Trailer Hitch Class
- Shop: Brake Controller
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Article: How to Measure for Trailer Hitch Drop
- Search Results: trailer hitch ball mount
- Video: Installing the Curt Trailer Hitch Receiver on a 2025 Toyota RAV4
- Q&A: Recommended SnapPad Jack Pads for a HWH Leveling System on a Motorhome
- Shop: etrailer Anti-Rattle Hitch Collar for 2" Hitch Receivers
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Search Results: hitch bike racks
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Video: Clean Up Your Trailer Wiring
- Shop: Roof Rack
- Article: My Trailer Hitch Doesn't Fit
on Trailer Hitch
