Replacement For Shelby 5776 Trailer Swivel Jack

Question

Question:

I’m looking for a direct replacement for the Shelby 5776 trailer jack.

asked by: Birch E

1

Helpful Expert Reply:

Although we don't offer a direct replacement, as Shelby is no longer in business, the Fulton # FTJ120W0301 would be compatible with the snap ring base your Shelby 5776 used. The jack has a 1200 lb capacity and offers 10 inches of lift. I'll link to a product demonstration video that you might find helpful.

expert reply by: Mike L

1

Customer Submitted Photo
(click to enlarge)

Answer 1

The rule of thumb for estimating a tongue weight is 10-15 percent of trailer weight. A 4,600 pound trailer would have a tongue weight between 460 and 690 pounds. Somewhere between a 1,000 to 2,000 pound capacity jack would be fine. Having a jack that…

view full answer...

Answer 2

The Shelby #5776 is the direct replacement for the #5756, but we do not offer that particular jack. The Fulton #FTJ120W0301 that you referenced would make an acceptable replacement. The capacity and the amount of lift or travel is identical. Both…

view full answer...

Answer 3

What we have heard is that the Fulton #FTJ120W0301 does fit the mounting plate of the Shelby Jack 5784 which is what it looks like you have something similar to.

view full answer...

Answer 4

If the holes on your mount are separated by 3 inches the Fulton trailer jack #FXP100W0301 will fit. If you need a new mount you'd need the #P9012-00. For new hardware for the bracket you'd need the #F0933325S00.

view full answer...

Answer 5

It sounds like your jack may use a weld-on mounting plate like #F500277 but I pulled one from the warehouse to measure its hole spacing and found those dimensions to differ from what you mentioned. The mounting hole spacing is 3-7/8-inches x…

view full answer...

Answer 6

Hey Andrew! Since it is a bolt-thru you can use the Fulton Boat Trailer Jack w/ Wheel #F1411300301 as a replacement. This typically mounts on the #P9012-00 which is a 4-1/2" square bracket with pin holes 3" apart on center. If you don't…

view full answer...

Answer 7

You will be able to use the Bolt-On Mounting Kit #F500349 with the Mounting Hardware #F500286 to bolt on the Fulton Bolt-Thru Swivel Marine Jack #FXP10W0301.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Replacement For Shelby 5776 Trailer Swivel Jack

Featured Help Information

Miscellaneous Media

Continue Researching