Installation of B&W Tow and Stow in Rise Orientation

Question

Question:

Do you slide it into your truck mount upside down to get the stated rise?

asked by: Don N

0

Expert Reply:

Yes. The B&W Tow and Stow # BWTS10033B would be installed "upside down" in order to be used in a rise configuration for your trailer.

expert reply by: Erik B

0

Answer 1

Yes, the B&W Tow & Stow 2-Ball Mount #BWTS10033B can absolutely be flipped to the rise position, which will provide as much as a 3-1/2 inch rise. This is a really nice ball mount that is compatible with 2 inch hitch receivers and features a…

view full answer...

Answer 2

The design of the B&W Tow & Stow 3-Ball Mount #BWTS20067BMP wouldn't allow for a secondary bracket and ball to attach a friction sway control kit, like part #83660. The only sway control you could use with this ball mount would an…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 8

Hey Kelvin, welcome back. To flat tow a 2026 Ford Maverick with your Demco Commander II Tow Bar item #DM9511012, I recommend the following parts: Baseplate Kit - Demco Tabless Base Plate Kit item #DM38CV Wiring Harness - Roadmaster Diode 7-Wire to…

view full answer...

Answer 9

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 10

Hey Steve, yes we do! Assuming you don't have the RamBox, the Black Armour Heavy-Duty Truck Bed Mat #BA72AR is what you're looking for. This has a 1/2" thick rubber construction and is custom fit for your Ram 2500. What are you typically…

view full answer...

Answer 11

Hi Richard! From the top of the shank to the lowest part where the tri-ball sits on the #BWTS20067BMP is 11.125". If you have the balls at max drop with the tallest one hanging down that would be 12.5". We recommend at least 11" of…

view full answer...

Answer 12

Thanks for all the details Mike, that helped a lot. For what you’re wanting to do, I’d recommend the Furrion Chill Cube 18,000 BTU ductless setup, #FR59TD in white or #FR27TD in black. Since you’re adding a separate rear bedroom AC and won’t need the…

view full answer...

Installation of B&W Tow and Stow in Rise Orientation

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching