Threaded Hitch Pin For Curt Hitch Bike Rack

Question

Question:

Receiver is 1 1/4 need replace threaded hitch pin

asked by: Stewart K

1

Helpful Expert Reply:

I spoke with Curt's customer service and they said if you are looking for an anit-rattle hitch pin the Trailer Hitch Anti-Rattle Kit for 1-1/4" Trailer Hitches, part # F-315, has a bolt that should work with your hitch bike rack. But without knowing the model hitch bike rack he could not 100% guarantee that it will work.

expert reply by: Mark Smith

1

Answer 1

The Trailer Hitch Anti-Rattle Kit, #F-315, is designed for use on 1-1/4 inch trailer hitch accessories that have a hollow shank. The block with nut is placed inside the shank and the nut is aligned with the hitch pin hole. When the threaded hitch pin…

view full answer...

Answer 2

Yes, in order to secure the Curt Cargo Carrier part #C18110 to the Draw-Tite Sportframe Trailer Hitch Receiver part #24915 that you have installed on your 2014 Kia Soul, you are going to want to use the Trailer Hitch Anti-Rattle Kit part #F-315. This…

view full answer...

Answer 3

For a Swagman 1-1/4 inch hitch bike rack you would want the part #S64029 and not the #F-315 which would not fit.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 7

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 8

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

Your picture is of an old Tekonsha Weathertronic electric brake controller. The wire color coding is as follows: White - Ground Black - Positive terminal on the battery Blue - To the trailer brakes Red - Cold side of the stop light switch. This will…

view full answer...

Answer 11

Hello Jerry. We do offer a lift kit for the 3,300 lb torsion axles. For that you can use the following: - Torflex Lift Kit - Single Axle - 2-5/8" Lift #K71-707-01

view full answer...

Answer 12

We don't have the specific pin, but I have a solution for you. Since Breakaway Switches are universal, I recommend you replace the entire switch with part #3802348 to go with your ESCO breakaway systems.

view full answer...

Threaded Hitch Pin For Curt Hitch Bike Rack

Product Page this Question was Asked From

Continue Researching