Snap Ring Swivel Dutton Lainson Jack to Replace Boat Trailer Jack

Question

Question:

I Need a new boat trailer tongue jack. My boat trailer welded on mounting hole dimensions are 5 1/2inch X 3. Please suggest a jack. Picture is my current broken jack.

asked by: Mark

0

Expert Reply:

For a snap ring Dutton Lainson jack to replace what you have on your boat trailer the part # DL22680 would be a great option with a slightly higher capacity at 2,000 lbs.

expert reply by: Jameson C

0

Answer 1

For the factory crossbars on your 2012 Subaru Outback, I would recommend the Malone Foam Block Rooftop Canoe Carrier, part #MPG156. The foam blocks used to support the canoe can be mounted to the crossbars, or can be placed directly on the roof…

view full answer...

Answer 2

We do offer both replacement parts and complete Dutton Lainson trailer jacks. All complete jacks can be view by clicking on the linked page. All Dutton Lainson jack replacement parts can be viewed by clicking on the other featured link. You can use…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Snap Ring Swivel Dutton Lainson Jack to Replace Boat Trailer Jack

Product Page this Question was Asked From

Continue Researching