Roadmaster Direct-Connect Base Plate Kit Pin Hole Size

Question

Question:

What size is the hole for the pin?

asked by: Tim P

0

Expert Reply:

According to Roadmaster the hole size for the pin on Item # 1437-3 is .770 inches.

expert reply by: Kevin C

0

Answer 1

I spoke with my contact at Roadmaster and I have the following measurements for the Roadmaster MS Base Plate Kit - Fixed Arms Item #1437-3. The rectangular plate is 6-11/16 inches long by 4 inches tall overall. The mounting holes are spaced 5-3/16…

view full answer...

Answer 2

It looks like you have a car side in the picture. You can get a set of replacements using #RM-222. I would recommend replacing both so they wear the same. And for reference the tow bar side is #RM-221. The individual left and right sides are not…

view full answer...

Answer 3

The Roadmaster Direct-Connect Base Plate Kit #1437-3 are more of a universal fitment and are designed to match up to mounting holes spaced 5-3/16 x 2-1/2" apart on center (see attached photo). I'm not sure if these will match up to the…

view full answer...

Answer 4

Roadmaster makes a base plate kit that is designed specifically for the Rugged Ridge bumper like you have which is part #1437-3 which you could attach a Roadmaster tow bar like the Falcon 2 #RM-520 directly to.

view full answer...

Answer 5

Hey David, congratulations on the new truck! Yes, the Roadmaster Direct-Connect Base Plate Kit #RM45EQ is compatible with your Roadmaster Nighthawk #RM-676. As long as you have everything from the kit the Roadmaster Universal Hy-Power Diode Wiring…

view full answer...

Answer 6

Hey Jennings! We don’t currently carry any 2-way propane/AC combo models like your old Norcold, so if you want to go that route you will have to look around elsewhere and match up whatever you find to your existing cutout. For a 12V I recommend one…

view full answer...

Answer 7

Hi Stephen; yes, installation of the Curt Custom Base Plate Kit #C32KR will reduce ground clearance at the front of your Jeep. This hangs down below the bumper as seen in the photo below. The distance from the ground to the center of the brackets is…

view full answer...

Answer 8

Hello Dennis, good question. The etrailer Invisible Base Plate Kit #e86YR does not have a designated weight rating. It is rated for well over the GVWR of your truck, and then some. It will absolutely be compatible with a 10K tow bar with zero concern…

view full answer...

Answer 9

Hello Layne, thanks for getting in touch. So we can definitely help set your 2024 Ford F-150 up for flat towing. Sadly, the base plate from a Ford Ranger will not transfer over to an F-150, so you will need a new base plate. Here are the parts I…

view full answer...

Answer 10

Hey Bob, The Norcold Polar #NC63FR does offer a larger interior space at 8.2 cubic feet, but the over all dimensions are the same between that and the older model. I know the #NC63FR has a built in vent at the top and clearance at the bottom that air…

view full answer...

Answer 11

Hey Chuck, the cut-out dimensions for the Vitrifrigo DP2600IXD4-F-3 refrigerator #VT96FR are 52.9 inches in height and 23.4 inches in width. The depth for a flush mount is 23.69 inches. Would that work in you RV?

view full answer...

Answer 12

Thank you for the photo! It looks like you've got the Lionshead Liger wheel currently, which we do carry. With that said, we don't have a pre-matched combo available with this wheel, but can give you the part number for a new wheel and tire…

view full answer...

Roadmaster Direct-Connect Base Plate Kit Pin Hole Size

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching