Should Brackets of Lippert 3.0 Front Landing Jacks Rest on Jack Tab
Updated 04/29/2021 | Published 04/28/2021
Question:
Hello, I have a factory installed ground control 3.0 leveling system. We have twice had the front jacks slip within the mounting bracket. Where should the mounting clamp sit vs the weld tab on the Jack? Other systems I have seen the weld tabs are located on the sides and the bracket sits under them, touching. On my set up they are not close. Thank you,
asked by: Jay T
Expert Reply:
The bracket should be resting against the tabs of the jacks so that there's no chance it can slip. I am not sure what they were thinking when they installed yours like that but you need the direct contact between the bracket and the tab.
(click to enlarge)
Product Page this Question was Asked From
Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad - 4-Point Set
- Camper Jacks
- 5th Wheel Camper
- Stabilizer Jacks
- Steel
- 10001 lbs or More
- Electric Jack
- 36 Inch Lift
- Bolt-On
- 4 Jacks
- Lippert
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Bluetooth Control - 6-Point Set
- Shop: Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad - 4-Point Set
- Search Results: lippert camper jacks
- Video: How to Install the Lippert Ground Control 5th Wheel RV Leveling System - 2015 Forest River Vengeance
- Video: Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System Installation - 2020 Forest River Ch
- Shop: Circuit Breaker - 50 Amp - Perpendicular Mount Bracket - Cycling Auto Reset - Plastic - Type I
- Shop: Derale Automatic Resetting Circuit Breaker - 50 Amp
- Search Results: 50 amp breaker
- Search Results: 50 amp fuse
- Q&A: How to Determine if Lippert Ground Control 3.0 Will Fit 5th Wheel RV
- Q&A: Can Rear Jacks of Lippert Ground Control be 24 inches From Rear Axle
- Q&A: 6 Point Automatic Leveling System Recommendation 2010 Keystone Montana Fifth Wheel
- Q&A: Installation Of The Lippert Ground Control 3.0 Jack Leg Mounting Brackets
- Q&A: How Much Room on RV Frame Does Lippert Ground Control Middle and Rear Jacks Take Up
- Q&A: Mounting Plate Height of Replacement I-Beam Jack Bracket for Lippert Ground Control
- Q&A: Solutions To Add More Clearance For Lippert Ground Control 3.0 Jack Legs
- Shop: Trailer Hitch
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Article: Trailer Wiring Diagrams
- Search Results: trailer hitch
- Search Results: trailer tires and wheels
- Article: How to Measure for Trailer Hitch Drop
- Shop: Trailer Wiring
- Shop: Power Mountain Tallboy Off-Road Bottle Jack - 8-1/2" to 37-3/4" Lift - 6 Tons
- Article: 5 Things to Know About Weight Distribution Hitches
- Search Results: trailer jack
- Shop: Suspension Enhancement
- Shop: etrailer Anti-Rattle Hitch Collar for 2" Hitch Receivers
- Video: A Look at the Power Mountain Tallboy 6 Ton Off-Road Bottle Jack with a Military Cargo Trailer
- Article: 30-Amp and 50-Amp RV Service: What's the Difference?
