Replacement Jack for Shorelandr Trailer with Bulldog 130 Series Jack

Question

Question:

Looking for a replacement jack for this shoreland trailer, Jack is bulldog 130 series pics attached this bolted on and dont want to modify trailer hope you can help.

asked by: Fred H

0

Expert Reply:

While we do have similar swivel jacks that can be used on your boat trailer the specific type of pivot assembly you have is no longer around so we don't have anything that would bolt right up. The easiest solution is probably going to be a jack like the Fulton part # FTJ120W0301 which would require you to weld on a new mount to your trailer frame.

expert reply by: Jameson C

0

Answer 1

The Fulton Round, Snap-Ring Swivel Marine Jack - Weld On - Sidewind - 10" Lift - 1,200 lbs #FTJ120W0301 provides similar capacity and does have a Snap ring pilot hole diameter of 2-1/2"that lines up with your Bulldog Jack.

view full answer...

Answer 2

The perfect replacement jack that you would need would be the Dutton Lainson Sidewind Jack part #DL22560 that you referenced. It will bolt right up to your mounting bracket and has 12 inches of lift. Check out the review video I attached for this…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 10

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Replacement Jack for Shorelandr Trailer with Bulldog 130 Series Jack

Continue Researching