Availability of UO21-003 MOR Ryde X-Factor Adjustable Crossmember

Question

Question:

Is this the same as morryd part#UO21-003

asked by: Chris N

0

Expert Reply:

The MorRyde part number that is the same as the U021-003 is our part # MR33WR actually.

expert reply by: Jameson C

0

Answer 1

Grease Seal #RG06-050 is the replacement part for the Dexter 010-019-00. It is 1.719 inches inner diameter and 2.565 inches outer diameter. It is a fit for 3500 lb axles. This is a confirmed replacement cross-reference.

view full answer...

Answer 2

The Dexter D35 axle is a 3,500 lb trailer axle so for a bearing kit you would want the part #BK2-100 that you referenced.

view full answer...

Answer 3

The seal that your mentioned and seal set #RG06-050 have the same inner and outer diameters so yes, you can use set #RG06-050 in place of 17144.

view full answer...

Answer 4

Thanks for the measurements and additional information! To determine which MORryde Equalizer you need you'll want to measure the distance at the bottom of your current equalizers from the center to the center of the bolt holes. The MORryde item…

view full answer...

Answer 5

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 6

Hey Richard, thanks for reaching out! Yes, the MORryde X-Factor Crossmember for Standard Frame Hangers #MR33WR can be installed with the Roadmaster Comfort Ride #RM-2460-2570. Just as long as the X-Factor is installed on either of the end hangers as…

view full answer...

Answer 7

Hello Chris, For your 2022 Grand Design Reflection 31MB 5th wheel with the MORryde CRE 3000 and wet bolt kit, the right crossmember brace is the MORryde X-Factor Crossmember #MR33WR. It helps stabilize your suspension, reduces stress by up to 94%,…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Availability of UO21-003 MOR Ryde X-Factor Adjustable Crossmember

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching