Distance From Bottom to Mounting Hole On Lock N Roll Articulating Channel Tongue Trailer Coupler

Question

Question:

Hello. On the 2 wide channel. How high are the mount holes from bottom edge of the channel? Thanks

asked by: Mark S

0

Expert Reply:

In regards to the Lock N Roll Articulating Channel Tongue Trailer Coupler part # 336TS528, the distance from the bottom of the coupler base to the center of the mounting hole is 1-1/2".

expert reply by: Conner L

0

Lock-N-Roll Distance from Bottom To Mounting Hole
(click to enlarge)

Answer 1

Harbor Freight trailers have a bolt pattern of 4x101.6 (or 4 on 4 inch) or the 5 on 4-1/2 inch if you have 5 lugs. . The 225 x 8 isn't a size we carry, but we do have the Kenda 215/60-8 Bias Trailer Tire with 8" White Wheel - 4 on 4 - Load…

view full answer...

Answer 2

I went out to measure the Lock N Roll Articulating Trailer Hitch for 2" Receivers - Vehicle Side #336VS501 and found the distance from the center of the hitch pin hole to the back of the latching mechanism is about 6", the length from the…

view full answer...

Answer 3

Based on the images you sent in it appears your 2005 Starcraft RT10 does not use a traditional A-Frame coupler so the Lock N Roll #336TS504 will not work for your application. Instead you will need to measure the width between your frame rails the…

view full answer...

Answer 4

If I were installing the Timbren Axle-Less Suspension System, #A12WS545, on my trailer, I would use a 2 inch steel tubing with a wall thickness of 1/4 inch. I spoke with my contact at Timbren and he told me that they do not have a minimum thickness…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Hey TJ, thanks for reaching out. Those Goodyear Duratrac LT225/75R16 Trailer Tire with Eagle Aluminum Wheel #LH53MR are actually light truck (LT) tires, not trailer tires. The giveaway is the size designation: LT225/75R16. If they were trailer tires,…

view full answer...

Answer 12

Welcome back Gary. To replace a 2" coupler that fits a 2" wide trailer tongue our options are limited to the Channel Tongue Trailer Coupler item #CT-3001-Z. It's got the standard trigger latch. There's not many options for couplers…

view full answer...

Distance From Bottom to Mounting Hole On Lock N Roll Articulating Channel Tongue Trailer Coupler

Product Page this Question was Asked From

Continue Researching