Will DeeMax Replacement Grease Cap Fit in Place of Dexter Vortex 21-261

Question

Question:

will this work to replace dexter vortex 21-261 cap

asked by: donna

0

Expert Reply:

Hey Donna, yes the Replacement Grease Cap for Dexter/Tie Down Engineering Vortex Trailer Hubs # DE69NR that you referenced does work as a replacement for your Dexter 21-261 cap. How do you like the Vortex trailer hubs?

expert reply by: Jameson C

0

Answer 1

I wish I had a good answer for you, but since Kodiak was bought out by Dexter it seems they discontinued the 204 caliper in favor of using the 225 calipers. They both worked on 3500lb axles but the 225 was also able to be used on larger axles up to…

view full answer...

Answer 2

Hey Al, I have a solution for you but we don't have anything that is a direct replacement for the Kodiak 204 caliper including the DeeMax you referenced. . Since Kodiak was bought out by Dexter it seems they discontinued the 204 caliper in favor…

view full answer...

Answer 3

Hello James, thanks for reaching out. Both the kits you mentioned, the Hydrastar #HYD22FR and #HYD42FR are complete conversion kits for standard 3,500 lb axles. The difference is the calipers included with each kit. The #HYD22FR has stainless steel…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Will DeeMax Replacement Grease Cap Fit in Place of Dexter Vortex 21-261

Product Page this Question was Asked From

Continue Researching