Replacement For MaxxFan 10-4301K Circuit Board

Question

Question:

Maxxair vent 12 volt 4 speed fan. have no model # and motor is OK, does the MA10-04301K-V16 replace my old board? Im not sure! my old board is a 10-4301K.

asked by: Ronald J

0

Expert Reply:

You are on the money with the replacement circuit board you need for your MaxxAir 10-4301K, which is the following:

- Replacement Printed Circuit Board and Switch for MaxxFan Roof Vents # MA10-04301k-v16

I have added a link below to a video review for you to check out as well if you'd like to take a look.

expert reply by: Kyle S

0

Answer 1

According to my contact at Advent Air, their #ACDOM150 would be the correct replacement for your Dometic 459516.701C0 RV AC unit. The unit will replace your existing roof unit, and will plug into the existing distribution box and thermostat. The unit…

view full answer...

Answer 2

For your MaxxFan Plus Roof Vent w/ 12V Fan, Thermostat, and Remote #MA00-04500K, you're going to need to use the Replacement Printed Circuit Board for MaxxAir Powered Lift RV Roof Vents w/ Reversible Fan #MA10A21275K that you mentioned. The…

view full answer...

Answer 3

Thanks for the picture! Based on it I can tell that the correct circuit board is the part #MA10-04301k-v16 that you referenced! The series of fan you have is the 6401k.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Replacement For MaxxFan 10-4301K Circuit Board

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching