LED Trailer Taillights with 2 inch Between Mounting Holes and 2 Wire Design

Question

Question:

My 16 ft low boy utility trailer has a cracked brake/turn signal/running light. It has 2 wires on the rear turn/ brake light. All I see are 3 wire set up when I try to order.The light mount is a 2” double bolt plate. What do you have in an led that would match up to what I’m trying to replace? Please send links. Also, it looks like they used whatever color wire they had so nothing is the same color on either side. How do I tell which wire to connect to what? I have a good voltage meter, so... Thanks,

asked by: Cody D

0

Expert Reply:

For a 2-wire trailer taillight with 2 inches between the mounting studs and is also LED you'd want the part # STL8RGB for the passenger side and part # STL9RGB for the driver side.

The two wires you have to your current taillights will carry the running light circuit on one wire and the stop/turn on the other. So you'd need to use your circuit tester to test both wire by function when connected to a tow vehicle.

expert reply by: Jameson C

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

Hey Kelvin, welcome back. To flat tow a 2026 Ford Maverick with your Demco Commander II Tow Bar item #DM9511012, I recommend the following parts: Baseplate Kit - Demco Tabless Base Plate Kit item #DM38CV Wiring Harness - Roadmaster Diode 7-Wire to…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Hey Jairo. So we do not offer a direct replacement for the Norcold N611, but we do have a good replacement option for you. It really comes down to what will fit in your cutout space. Take a look at the Norcold RV Refrigerator w/ Freezer - 8.2 cu ft -…

view full answer...

LED Trailer Taillights with 2 inch Between Mounting Holes and 2 Wire Design

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching