Replacement Bulk Head Seal for BAKFlip MX4 Folding Tonneau cover

Question

Question:

Hello I have the Bakflip mx4 and a spray-in liner on my 2018 f150 platinum with 5.5’ bed. Which Replacement bulkhead seal would work for that? I don’t see the MX4 listed in the description for the 3/8inch replacement seal. Thanks

asked by: Max W

0

Expert Reply:

The replacement bulk head seal # PARTS-326A0005 will work great to replace the seal for your BakFlip MX4 tonneau cover. You will want to be sure to remove the old seal and clean the top of the bulk head with rubbing alcohol to make the surface clean for the installation of the new seal.

expert reply by: Jacob H

0

Answer 1

Hey Bob. There's two possible locations for the brake controller port on your 2026 Ford F-150. The most likely one is on your dash behind the coin holder above the 4WD knob. It'll be connected to the back of the coin tray which is only…

view full answer...

Answer 2

The Redarc Tow-Pro Liberty #RED24FR is the way to go over the Elite #RED44FR as you get the nicer functions of the Elite at a lower price. The Elite has the ability to be the more preferred proportional style of controller as well as a time-delayed…

view full answer...

Answer 3

Yes, you can install the Redarc Tow-Pro Liberty Brake Controller #RED24FR on your 2020 Ford F-150 XLT. You will need the Tekonsha Plug-In Wiring Adapter #22292 to connect to the factory connector on your F-150 that came with a 7-way towing connector.…

view full answer...

Answer 4

The Redarc Plug-and-Play Wiring Harness #331-TPH-007 is the correct harness for your 2022 Ford F-150. This will allow you to connect the Redarc Tow-Pro Liberty Brake Controller #RED24FR to your factory wiring.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 12

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Replacement Bulk Head Seal for BAKFlip MX4 Folding Tonneau cover

Continue Researching