Would Draw Tite Hitch 36548 Fit 2020 Dodge Charger Scat Pack

Question

Question:

Need a little guidance about this hitch!!! Will it fit under a 2020 scat pack charger without having to destroy the rear valance????

asked by: Brad Y

0

Expert Reply:

The Draw Tite hitch part # 36548 does fit your 2020 Dodge Charger Scat Pack but will require some trimming of the lower rear fascia. I wouldn't say it would destroy the valence but it does require trimming which is a very common step for the install of hitches.

expert reply by: Jameson C

0

Answer 1

Yes, there is. To add a 2" hitch to your 2018 Charger, I recommend the Draw-Tite Trailer Hitch item #76145. This hitch is custom fit and bolts to your Charger with included hardware. It is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 2

I have included a link to the installation instructions for the Draw-Tite trailer hitch #36548. There is no mention of having to cut, trim, or drill anything for installation. The hitch comes with the correct ball mount, pin, and clip. For a 1-7/8…

view full answer...

Answer 3

All of the hitch receivers available for your 2016 Dodge Challenger will show some of the cross tube. However, the Curt Class II #C12064 and Curt Class III #C13093 do have the receiver opening welded under the tube unlike the Draw-Tite Class II…

view full answer...

Answer 4

Yes, Curt trailer hitch #C13093 and #C12064 will fit your 2015 Dodge Charger. Note the 2015 Dodge Charger, the drivers side exhaust must be temporarily lowered and drivers side muffler removed and then reattached in order to install Curt trailer…

view full answer...

Answer 5

The least visible hitch we have for your 2016 Dodge Charger Scat Pack is going to be the Draw Tite #36548 that you referenced. This hitch has a 1-1/4 inch opening which would be smaller than the 2 inch hitches and due to it's safety chain loop…

view full answer...

Answer 6

The trailer hitch I recommend for your 2016 Dodge Charger is the Draw-Tite Trailer Hitch Receiver, Class II #36548. This trailer hitch has a 1-1/4 inch receiver that will work well with your Thule Vertex. The #36548 hitch has been confirmed to fit…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 11

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Would Draw Tite Hitch 36548 Fit 2020 Dodge Charger Scat Pack

Continue Researching