Roadmaster EZ2 Base Plate Installation on a 2013 Ford C-Max

Question

Question:

do the brackets just bolt to the c-max frame? do you have to cut any part of the grille to mount the brackets? can you send me a copy of the installation instructions?

asked by: John G

1

Helpful Expert Reply:

The Roadmaster EZ2 Base Plate Kit, # 524432-1, bolts to the bumper core and subframe of your 2013 Ford C-Max. I have attached a link to the installation instructions for you to check out. The instructions include photos of the installation steps. Roadmaster also requires red loctite, # LT37420, to be used on all bolts.

There may be some fascia trimming required on your C-Max. The receivers for the draw bars will require an opening on both sides of the lower front grille. Check out the photo that I attached showing the area that needs to be trimmed. The fascia trimming is also explained in the installation instructions on page 7.

Keep in mind, the base plate kit will only fit the Hybrid SE and SEL models. At this time there are no base plate options for the Energi models.

expert reply by: John H

1

click to enlarge

Answer 1

I took a look at the online owner's manual for your 2018 Chrysler Pacifica, and it says flat towing with all four wheels on the ground is not allowed, but so long as it is a front-wheel drive, you can tow it behind your motorhome using a tow…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Roadmaster EZ2 Base Plate Installation on a 2013 Ford C-Max

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching