Replacement Grease Cap Plug for 6,000 lb Dexter Hub

Question

Question:

I need rubber lube plugs for grease caps on a 6000 lb 8 lug axle. Can you tell me what part # I need? Thanks

asked by: Terry L

0

Expert Reply:

A 6,000 lb Dexter hub uses the grease cap of the RG04-120 so for a replacement cap plug you'd need the # RG04-010.

expert reply by: Jameson C

0

Answer 1

Can you please provide me with the exact part numbers that your are referring to?

view full answer...

Answer 2

Hey Mike, the two Karrier tires part #KE63KV and #AM10303 are very similar but the big difference is the tread pattern. I prefer the part #AM10303 as it is more similar to an automotive type tread pattern but the cost savings of the #KE63KV is pretty…

view full answer...

Answer 3

The part you were looking at, Redline part #RG04-010 is designed to replace the caps on Dexter EZ Lube axles. If your trailer has Dexter EZ Lube axles this part will fit.

view full answer...

Answer 4

Great question, William! The Karrier ST225/75R15 #KE63KV is a KR35 while the Karrier ST225/75R15 #AM10303 is a KR03 according to Kenda. There is a slight variation in the tread pattern and from what Kenda says about them it looks like the KR03 is…

view full answer...

Answer 5

In regards to the Replacement Lid for Hopkins Engager Break-Away Kit part #20106, Hopkins does not offer just the sticker separately so if yours is worn or missing you'd need to replace the entire lid. I know this is not what you were looking to…

view full answer...

Answer 6

You are correct, the only difference between the #8-219-4UC3-EZ and #42866UC3-EZ is the ID of the grease seal. The #8-219-4UC3-EZ uses a grease seal that has a 2.125 inside diameter while the #42866UC3-EZ uses a seal with a 2.250 inside diameter.

view full answer...

Answer 7

We have 2 different options for you to use to upgrade your 5,200 lb axles from 6 bolt to 8 bolt with 1/2 inch studs. Dexter Axle has the Trailer Hub Assembly, part #8-231-9UC1-EZ, which is black in color and comes with the hub, inner bearing, part…

view full answer...

Answer 8

The only difference between the two hubs is the inside dimension of the grease seal included with the hub drum. The #42866UC3-EZ uses a 10-36 grease seal with a 2.25 inch inside diameter and the #8-219-4UC3-EZ uses a 10-10 grease seal that has a…

view full answer...

Answer 9

The difference between the 10-10 grease seals, #RG06-090, and the 10-36 grease seals, #RG06-070, is their inner diameter. The 10-10 grease seals fit older spindles with a seal journal (see photo) diameter of 2.125 inches. The 10-36 grease seals fit…

view full answer...

Answer 10

It sounds like there is an electrical short on your trailer wiring that is activating your left rear brake assembly and that is why the brake continues to drag and get hot. Since you have swapped the brake assembly out and still had the problem you…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Replacement Grease Cap Plug for 6,000 lb Dexter Hub

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching