Replacement 3/4 Inch Bolts for Fastway e2 Weight Distribution System
Updated 03/19/2021 | Published 03/17/2021
Products Featured in This Question
Question:
Guy that installed my 10000# e2 hitch galled up the ¾ bolt/nut. He replaced both with grade 8 bolt, nut, and lock washer. Is this acceptable?
asked by: Gary K
Expert Reply:
According to Fastway, the 3/4 inch plated bolts they use are grade 5, but you'll want to use 3/4 inch conical toothed washers and lock nuts. The lock nuts can be found locally, but not the washers and Fastway won't honor the warranty if hardware other than what they recommend is used. If the guy buggered up the nut and bolt, I'd make him replace them using hardware from their # FA92-02-9600 hardware kit since he and not you damaged it.
Product Page this Question was Asked From
Fastway e2 Weight Distribution w/ 2-Point Sway Control - Trunnion - 10,000 lbs GTW, 1,000 lbs TW
- Weight Distribution Hitch
- WD With Sway Control
- Trunnion Bar
- Fits 3 Inch Frame
- Fits 4 Inch Frame
- Fits 5 Inch Frame
- Fits 6 Inch Frame
- Includes Shank
- Top-Mount
- Fits 2 Inch Hitch
- Allows Backing Up
- 800 lbs
- 900 lbs
- Fastway
more information >
Featured Help Information
Instructions
Continue Researching
- Search Results: fastway e2 shanks
- Search Results: wdh shank
- Search Results: weight distribution shank
- Search Results: weight distribution hitch
- Search Results: shank
- Article: How to Measure for Trailer Hitch Drop
- Video: Comprehensive Review: Locknut
- Q&A: Replacement Bearing Kit for Tie-Down/Dexter 3.5K Torsion Axle
- Shop: Truck Topper
- Q&A: Replacement Bearing Kit for 3,500 lb Dexter Torsion Axle
- Shop: Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Shop: Dexter Trailer Hub & Drum Assembly for 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 - Pre-Greased
- Shop: Complete Bearing Kit with L44649 Inner/Outer Bearings and 10-9 Grease Seal Fits 1.063" Spindles
- Shop: Timken Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Shop: Replacement Hardware Kit for Fastway e2 Weight Distribution Head - Round and Trunnion Bar
- Q&A: Weight Distribution Shank for Fastway e2 with More Drop and Longer Shank than Included Shank
- Q&A: Is Fastway e2 WDH Compatible With Other Brand Shanks
- Q&A: Recommended 7 Drop Shank For Fastway e2 Weight Distribution System
- Q&A: Tip for Torquing Hitch Ball of Fastway Weight Distribution System
- Shop: Fastway e2 Weight Distribution w/ 2-Point Sway Control - Trunnion - 10,000 lbs GTW, 1,000 lbs TW
- Shop: Locknut - 3/4" Diameter - Zinc Plated
- Search Results: e2 fastway
- Search Results: ts20040b
- Video: Replacement 4.3" Monitor for Furrion Vision S Wireless RV Camera System: The Breakdown
- Q&A: Does the Replacement Bolts for Fastway e2 Weight Distribution Head Comes With Conical Tooth Washers
- Video: Replacement Hardware Kit for Fastway e2 Weight Distribution Head Review