Tip for Torquing Hitch Ball of Fastway Weight Distribution System
Updated 02/05/2019 | Published 02/04/2019
Question:
Hello: I just received my FA92-00-10000 Fastway e2 Weight Distribution hitch. Step 2 in the instruction manual is to install the ball onto the head and torque to 450 ft lb. Ive got the appropriate socket and torque wrench. My question is how to go about it. Is this procedure correct - put the shank into the trucks receiver and hitch pin - attach Trunnion Hitch Head to the shank by hand tightening the shank bolts - attach ball and tighten to 450 ft-lb using a torque wrench on one side and an open end or crescent wrench on the other side. I was wondering if it would be better to do Step 3 from the install instructions and also tighten the shank bolts to 250 ft lb before installing the ball so that the shank/head would be more rigid? thanks,
asked by: Kerry T
Helpful Expert Reply:
I would recommend using the exact procedure you outlined. Tighten the shank bolts first and then with the shank in the vehicle hitch (secured with hitch pin) torque down the hitch ball to 450 ft lbs.
Product Page this Question was Asked From
Fastway e2 Weight Distribution w/ 2-Point Sway Control - Trunnion - 10,000 lbs GTW, 1,000 lbs TW
- Weight Distribution Hitch
- WD With Sway Control
- Trunnion Bar
- Fits 3 Inch Frame
- Fits 4 Inch Frame
- Fits 5 Inch Frame
- Fits 6 Inch Frame
- Includes Shank
- 2-5/16 Inch Ball
- Fits 2 Inch Hitch
- Allows Backing Up
- 800 lbs
- 900 lbs
- Fastway
more information >
Featured Help Information
Instructions
Continue Researching
- Video: Comprehensive Review: Locknut
- Article: How to Measure for Trailer Hitch Drop
- Search Results: fastway e2 shanks
- Search Results: weight distribution shank
- Search Results: weight distribution hitch
- Search Results: shank
- Search Results: wdh shank
- Shop: Truck Topper
- Q&A: Replacement Bearing Kit for Tie-Down/Dexter 3.5K Torsion Axle
- Q&A: Replacement Bearing Kit for 3,500 lb Dexter Torsion Axle
- Shop: Trailer Wheel Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Shop: Replacement Bearing Kit with Bearings L44649, Races L44610, Seal 10-9 - Fits 1.063" Spindles
- Shop: Dexter Trailer Hub & Drum Assembly for 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 - Pre-Greased
- Shop: Timken Bearing Kit for 3,500 lb Axles with #84 Spindle - Bearings L44649/L68149
- Q&A: Recommended 7 Drop Shank For Fastway e2 Weight Distribution System
- Q&A: Is Fastway e2 WDH Compatible With Other Brand Shanks
- Q&A: Replacement 3/4 Inch Bolts for Fastway e2 Weight Distribution System
- Q&A: Weight Distribution Shank for Fastway e2 with More Drop and Longer Shank than Included Shank
- Shop: Fastway e2 Weight Distribution Shank - 12" Long - 12-1/2" Rise 9-3/4" Drop - 1.2K TW
- Shop: Fastway e2 Weight Distribution w/ 2-Point Sway Control - Trunnion - 10,000 lbs GTW, 1,000 lbs TW
- Shop: Replacement Hardware Kit for Fastway e2 Weight Distribution Head - Round and Trunnion Bar
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Video: Firestone Ride-Rite Air Bags with Easy Mount Compressor Feature Breakdown
- Search Results: trailer hitch
- Search Results: trailer tires and wheels
- Shop: Trailer Wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Suspension Enhancement
on Weight Distribution Hitch
