I Need a 20 Inch Propane Tank Pigtail Hose with a Type 1 x 1/4 inch NPT Fitting

Question

Question:

I an looking for a 20 propane hose pigtail with braided line 1/4 npt x type 1 have anything?

asked by: Stan T

0

Expert Reply:

I'm assuming you are asking for a 20 inch hose, which the closest option we have at this time would be the combination of our pigtail hose, part # 100833-24, and adapter # 204120-MBS. If you don't mind using a typical rubber hose, you can use part # 37207-30865.

expert reply by: John H

0

Answer 1

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 2

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

Hi Thomas, From what info I could find, your 2026 Alliance Avenue 30bh comes with a Lippert Rota-Flex pivoting pin box that uses the Lippert Rhino pin box bolt pattern. The B&W 5th Wheel to Gooseneck Pin Box part #BW23RV is what I'd suggest…

view full answer...

Answer 5

Hey Steven, this is a great question but yes the correct bearing kit you need for your 2025 Grand Design 27BH with 5,100 lb axles is the kit for 5,200 lb axles part #BK3-300 which comes with the correct bearings, races, and seal. Did you have a…

view full answer...

Answer 6

The difference between the prices of the JR Products Automatic Changeover LP Gas Regulators and Camco Automatic Changeover 2-Stage Propane Regulators are in the BTU per hour, which as you correctly noted, is important information. The JR Products…

view full answer...

Answer 7

Welcome back Bill. The MEC RV Propane Bulkhead Fitting item #MEC84CR does not include a lock nut. I ran down to the warehouse and measured it. The threaded portions are 1-1/8" long and 5/8" long. It's definitely long enough to get…

view full answer...

Answer 8

Thanks for the picture Ken! The LaSalle Bristol Drain Valve item #LSB44AR is exactly what you need. I checked with Grand Design and the 1-1/2" diameter fittings match up to what came on your trailer from the factory. To remove the old drain…

view full answer...

Answer 9

Hi Robert, You found the perfect replacement for your Marshall MEGR-253 with the JR Products Compact Automatic Changeover 2-Stage Propane Regulator #37207-31525. This has the same fittings as the Marshall, but is higher quality, with a higher Btu…

view full answer...

Answer 10

Yes, the pivot pin part #58484 that you referenced will fit your Reese 15k fifth wheel hitch. Reese up-rated their 15k hitches a few years back so the parts for a 16k are going to be the same as a 15k.

view full answer...

Answer 11

The Atwood GE16EXT 10 gallon water heater has 23.5" x 19.4" x 18.2" dimensions so you'll have to make alterations to the cutout hole to fill in the gap from any of the water heaters we carry. I recommend the Furrion RV Tankless…

view full answer...

Answer 12

I'm seeing multiple dimensions for the Atwood GE16EXT RV water heater and all of them are quite a bit larger than the current models that we offer. With the change over to tankless systems manufacturers have also decreased the size as technology…

view full answer...

I Need a 20 Inch Propane Tank Pigtail Hose with a Type 1 x 1/4 inch NPT Fitting

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching