Option For Trailer Fenders Close to 25 x 8 For 12 Inch Wheels

Question

Question:

I have a 1976 Spartan trailer with 12 inch wheels. The current fenders are 25x8. Looking to replace them. Can you help.

asked by: Jeff

0

Expert Reply:

We have a couple of options that may work for you that are designed to work with trailers that have 12 inch wheels and are very close to the 25" x 8" fenders you currently have. One is rounded and one is a Jeep-style (more square) and if you can go with slightly different dimensions then you can can choose from either of the following:

- 25-3/4" long x 7" wide x 10-5/8" tall: Single Axle Trailer Fender - Rounded Edges # HP64FR

- 24" long x 8" wide x 8" tall: Single Axle Jeep Style Trailer Fender # HP99VR

If you need mounting brackets as well, the correct part is the Mounting Brackets for Trailer Fender - 8"/12" Wheels # CE26061G-2.

I have added some links below to video reviews for you to check out as well of these fenders.

expert reply by: Kyle S

0

Answer 1

If by radius you mean the length of a line segment from the center of a sphere to its perimeter then it is 11-3/4 inches given that the overall length of the fender #CE17701G is 23-1/2 inches. Because the fender is not a true half circle, this does…

view full answer...

Answer 2

Hello Mark, thanks for reaching out. I looked over a few pictures of these 2007 5x10 snowbear utility trailers, and we may have a fender that will work as a replacement, but we do not have anything that will directly replace it as far as bolting…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Option For Trailer Fenders Close to 25 x 8 For 12 Inch Wheels

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching