Recommended Replacement RV Scissor Jacks

Question

Question:

I was shopping for upgraded RV scissor stabilizer jacks.

asked by: Travis M

0

Expert Reply:

The upgraded scissor stabilizer jacks that I recommend are the Leveling Scissor Jacks with Handle part # JSC-30 which have a 10,000 lb capacity and offer up to a 30" lift. They also come with an easy to use crank handle. They can be bolted or welded to the frame.

expert reply by: Conner L

0

Answer 1

Hey Robert. Our highest capacity scissor jacks are going to be the etrailer Scissor Stabilizer Jacks. They come in a 4-pack item #e74RV or a 2-pack item #e96VV and have a 7,500 lbs capacity per jack. We do have ones rated for 10,000 lbs apiece. What…

view full answer...

Answer 2

Hey James! It comes down to whatever is the easiest way to mount them and access the jack with a crank handle. The Lippert Scissor Stabilizer Jack item #LC285325 you were looking at can be mounted in either orientation. I have linked an installation…

view full answer...

Answer 3

To answer the last question first, a stabilizer jack such as #JSC-30 would be used until there was just enough tension to keep the trailer or RV from rocking. For actual lifting you would need a different device. So assuming that the RV was level…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 10

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Recommended Replacement RV Scissor Jacks

Product Page this Question was Asked From

Continue Researching