Will LaSalle Bristol 3" RV Sewer Slip Hub Fit 3" ABS Drain Pipe On RV

Question

Question:

LaSalle Bristol RV Sewer Slip Hub with Flange - 3 - 34466V13 Will this fit on 3 ABS drain pipe. I am rerouting two LaSalle Bristal valves on the output side to the side of my RV because the drain hits the ground going into gas stations. It currently points to the back of the RV.

asked by: Tom D

0

Expert Reply:

The LaSalle Bristol RV Sewer Slip Hub with Flange - 3" # 34466V13 you were looking at will work with the 3" ABS drain pipe on your RV.

The hub side will bolt to your black water waste valve that you mentioned.

You will also need the LaSalle Bristol ABS Solvent Cement # 3447530889 to secure the ABS pipe to the Slip Hub # 34466V13.

I included a video of the # 34466V13 for you to take a look at.

expert reply by: Samuel C

0

Answer 1

The Valterra RV Sewer Spigot with Flange - 3" #T1006 will be compatible with LaSalle Bristol Valves. This has the standard mounting holes 3-3/4 inches apart on center. Then you will simply use the solvent cement like #A05-0303 or #3447530889 to…

view full answer...

Answer 2

You should be able to tell which Valterra Double RV Waste Valves you need by inspecting your current connection points. The one end with the lugs on it is the same on all 3 parts so you simply need to determine if you need hubs, spigots, or a…

view full answer...

Answer 3

Hello Mark, Per the tech at Lippert you are going to want to use AW-32 Hydraulic Fluid, and not an automatic transmission fluid.

view full answer...

Answer 4

The LaSalle Bristol Motodrain Electronic Waste Valve #LSB42TR switch is not weatherproof. You don't have to mount it completely inside but I would run the wire over to a nearby compartment and mount it on the compartment wall for extra…

view full answer...

Answer 5

Hi Tom, The LaSalle Bristol Motodrain Electronic Waste Valve #LSB42TR switch has three positions because it has an extend (close), retract (open), and idle position.

view full answer...

Answer 6

I don't know the length of the cable used for valves on your Montana so you'll want to measure the length to determine the correct replacement. To make the swap out easy I recommend just unbolting the old valve from the system and then swap…

view full answer...

Answer 7

In order to help prevent leaking between the grommet and tank on the Replacement Rubber Grommet for RV Black Water Tanks part #F02-2106 it would be wise to use a sealant like part #LT37467 between the two surfaces. I am not sure if this is a…

view full answer...

Answer 8

The MORryde Cushioned 5th Wheel Pin Box #MR84VR weighs right at 190 pounds. Due to this, it will ship freight. Just in case you needed, this is designed to fit 14,000 to 18,000 pound trailers with the Lippert 1621 and 1621HD pin boxes.

view full answer...

Answer 9

The manufacturer and model number of the pin box is usually printed on a sticker or stamped into a plate or directly into the metal of the pin box. If you can't find that, the manufacturer of your 5th wheel should be able to tell you which pin…

view full answer...

Answer 10

That's a great question, John! Yes, you can use the etrailer Replacement Fabric #e26QV in place of the Solera Replacement Fabric #LCV000334415. They are both made to work on the same size awning, so the fabric will be the same size and will…

view full answer...

Answer 11

Hello Kevin, Thanks for writing in. The main difference between the Power Watchdog Surge Protectors #HU67FR and #HU42VR comes down to the monitoring capability, housing design, and surge protection rating. The #HU67FR is the newer Generation 2 model.…

view full answer...

Will LaSalle Bristol 3" RV Sewer Slip Hub Fit 3" ABS Drain Pipe On RV

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching