The part # D50-2880 has an outer diameter of 1-1/2 inch so the correct flange you'd need to fit it is the part # T1005-1. You'll need ABS solvent part # A05-0303 too and you'd be set. view full answer...
I do see what you are saying, and though we do have a solution, your hoses do not have the appropriate connections for the RhinoFLEX RV Sewer Hose T-Adapter for 90-Degree Elbow Fittings # CAM39734.
What I strongly recommend instead that will fix your problem is the Flush King Reverse Flush Valve for RV Holding Tanks and Sewer Hoses - 3" Diameter # F02-4350 because it is designed for the exact problem you are having. It will flush the hoses so the waste water does not stay the "T" on... view full answer...
The Valterra RV Sewer Spigot with Flange part # T1006 has a spigot fitting which means it will slide into a 3" diameter sewer pipe and the Valterra RV Sewer Slip Hub with Flange part # T1005 has a hub fitting which means it will slide onto a 3" diameter sewer pipe. view full answer...
To widen your 1-1/2" pipe to 3" using the Valterra Eccentric Tank Reducer - RV Gray Water - 3" Spigot to 1-1/2" Hub # T1041-1 you would first need the Valterra DWV Adapter for RV Sewer System - ABS Plastic - 1-1/2" Hub to FPT # D50-2922 to screw onto your current fitting. The # T1041-1 would then slide over the 1-1/2" hub fitting of the # D50-2922 allowing you to connect a 3" pipe to your sewer system.
Between these two fittings you'll want to use some ABS Solvent Cement # A05-0303... view full answer...
You'll first want to attach the LaSalle Bristol Clean Out Adapter for RV Sewer System # 344633703 to your current setup and then you can attach either the Valterra RV Sewer Termination Adapter # T1029-2 or the Valterra Rotating Adapter for Rigid RV Sewer Pipe # T1028 to the unthreaded side of the # 344633703 with some Valterra ABS Solvent Cement # A05-0303 view full answer...
Yes, of course you can insert and glue the Valterra Rotating Adapter for Rigid RV Sewer Pipe, # T1027 if you choose to. If your objective is to have a permanent/semi-permanent arrangement of your RV to a sewer system, I suggest the Valterra Rotating Adapter for Rigid RV Sewer Pipe, # T1028. This adapter converts an RV waste valve to connect to 3" hub sewer pipe. The bayonet fitting rotates, making it easy to connect to the lug fitting on your RV's waste valve and the 3" hub slides over... view full answer...
From what I can gather it sounds to me like you need the Valterra Eccentric Tank Reducer - RV Gray Water - 3" Spigot to 1-1/2" Hub # T1041-1. The 3" Spigot mounts directly in the gray water tank outlet while the 1-1/2" Hub slides over sewer pipe.
Then for a 1-1/2" diameter gray-water sewer pipe we have the LaSalle Bristol Cable-Actuated RV Waste Valve for Gray Water Tank. This is valve is available in with cables that are numerous lengths, which I'll list for you so you can choose the... view full answer...
All of our hoses and fittings are for the standard fit bayonet which is not what you have. You can either use the adapter # T05-2285VP you referenced to adapt the older thetford fittings to the standard bayonet or if you don't want an additional adapter I recommend replacing current fitting with the Valterra RV Sewer Termination Adapter - 3" Lug Fitting to 3" Hub # T1029-2. view full answer...
So the difference is purely in how the two connect to your sewer pipe, which will also tell you which one you need; one will slide into the pipe (the spigot) while the other will slide onto the pipe (the hub):
- Slide Into Pipe: Valterra Waste Valve for RV Black Water Tank - 3" Spigot to 3" Lug # T50A
- Slide Onto Pipe: Valterra Bladex Waste Valve for RV Black Water Tank - 3" Hub to 3" Lug # T50
To secure the valves to your pipe you would just need the Valterra ABS Solvent Cement... view full answer...
Ok so it sounds like what you are wanting to do is just replace your black water tank's waste valve, and I can let you know how to determine the correct one, as there unfortunately isn't a way for us to know the exact valve for your R-Pod.
It's pretty simple though, because you just need to know if the valve you are replacing slid over your pipe or into your pipe.
If both ends of your waste valve slid into your sewer pipe you will need the Valterra Bladex Waste Valve for RV Black... view full answer...
When installing the Valterra Eccentric Tank Reducer # T1041-1 to your existing tank with a 3" opening you will just need to use some ABS solvent cement like # A05-0303 for the attachment. This is also what you will use to add the LaSalle Bristol Cable-Actuated RV Waste Valve # 34466N11AB48GMA to the fitting.
You will want to coat the outside AND inside of each fitting with the solvent before connecting the components. What this does is actually cause a chemical reaction with the plastic... view full answer...
Since your current pipe has a 3-1/2 inch outer diameter it most likely has a 3 inch inner diameter (measure this to be sure) which would mean that you'd need a 3 inch spigot to lug fitting adapter like part # T1029-1 as this will slip into the pipe and give you the type standard lug fitting for the standard size bayonets to attach to. view full answer...
The Valterra Eccentric Tank Reducer part # T1041-1 has a 3" spigot end which installs inside the neck on the waste water tank and then a 1-1/2" hub end which you would slide a pipe into. In order to secure the spigot end into the neck on the tank you will want to use some gasket maker part # LT37467 on the outside of the spigot fitting or on the inside of the water neck and then use a band clamp part # H03-0009 to clamp down on the waste water neck and hold the spigot fitting in place.... view full answer...
Thank you for the photos! Based on that it looks like you have a spigot to hub black water tank valve, like you mentioned, where the hub end fits over one pipe and the spigot end fits into the other pipe. So for a spigot to hub replacement valve with a 72 inch cable you will need the following:
- LaSalle Bristol Cable-Actuated RV Waste Valve for Black Water Tank - Spigot to Hub - 72" Cable # 34466N4AB72GMA
Then to complete the install you will just need the LaSalle Bristol ABS Solvent... view full answer...
In order to connect to the Valterra Gray Water Drain Connector part # T01-0091VP which has a 3/4" MPT fitting you can use the Valterra Flushing Hose for RV Sewer System part # W01-4180 which has the correct 3/4" FPT fitting that you need to do so. This is the shortest length we offer with for this hose. view full answer...
The two flanges are essentially the same thing but made by two different companies so either the # 34466V13B or the # T1009 would work great. view full answer...
What you can do is hook the Valterra Eccentric Tank Reducer - RV Gray Water - 3" Spigot to 1-1/2" Hub Item # T1041-1 onto your 1-1/2" pipe using some Valterra ABS Solvent Cement - 1/4 Pint Item # A05-0303 and a hose clamp.
Next you'll hook in the Valterra RV Sewer Termination Adapter - 3" Lug Fitting to 3" Spigot Item # T1029-1 using some # A05-0303 and a hose clamp.
If your hose has the bayonet end or if you have no end on the hose you can just hook it in as well using a hose clamp. view full answer...
You're right, a picture of the flange-to-flange width is definitely a good idea, so I contacted the manufacturer, Valterra, to get the dimension, and then went ahead and made a photo for you of the Valterra elbow you asked about:
- RV Sewer Elbow - 2-Way - 3" Hub x 3" Rotating Flange x 3" Rotating Flange # T1039-1
As you can see by the accompanying photo, the distance between the two flanges is 6 inches. I have also added a link below to a video review of the # T1039-1 if you'd like... view full answer...
It sounds like you're going to need the Valterra Eccentric Tank Reducer # T1041-1 which will mount directly to your 3" spigot, while the 1-1/2" hub slides over the sewer pipe.
Now you can connect to the Valterra Waste Valve for RV Gray Water Tank w/ Cap # T1001C, like you mention.
From here, you can attach the Valterra Gray Water Drain Connector # T01-0094VP for the 3/4" hose connection, or you can use # T01-0091VP if you want a 90° angle 3/4" hose connection.
We have various... view full answer...
Looking at the picture you provided it's either the Valterra Street DWV Fitting for RV Sewer System - 90 Degree - 1-1/2" Spigot to 1-1/2" Hub Item # D50-2880 or Valterra Street DWV Fitting for RV Sewer System - 90 Degree - 3" Spigot to 3" Hub Item # D50-2882. You'll just need to measure the pipe to see if it's 1-1/2" or 3" in diameter. view full answer...
The Valterra Double Elbow DWV Fitting, # D50-3047, measures 9 inches from end to end. Also, from the horizontal opening to the vertical opening the measurement is 7 inches. view full answer...
The Valterra Eccentric Tank Reducer, part # T1041-1, is installed with cement. When you reinstall the new one use # A05-0303.
The cement is permanent so you're not going to be able to break it up. Instead you need to cut the pipes after removing the hose clamps. Then replace it with the new one and apply the new cement.
The same cement can be used on other plumbing parts as well. view full answer...
The Camco RV Drain Trap, part # CAM37262 is designed for 3/4 inch diameter drain hoses.
The threaded inlet portion of the trap measures 1-3/4 inches at the threads as shown in the attached photo. If your drain hose is 3/4 inches in diameter I am sure you could make this work for you. You may have to enlarge your drain to get this to fit and replace. view full answer...
The LaSalle Bristol RV Sewer Termination Adapter # 34466V293B3S is designed to slide into a larger hub like what you see on the end of # T1028 and secured using ABS Solvent Cement # 3447530889. The inner diameter on the hub should be about 3-1/2 inches. If this is what is on the PVC pipe that you mentioned then it will work great.
I don't recommend connecting it directly to another 3 inch diameter PVC pipe though, as this might not allow for the best connection even when using a healthy... view full answer...
The Easy Slip RV Gray-Water Drain Adapter # CAM39111 will work, but I recommend the Valterra Gray Water Drain Adapter for RV Black Water Waste Valve # T1020-5VP. This will give you a cleanout for your black water tank. view full answer...
The Camco RV Drain Trap for 3/4-Inch Diameter Drain Hoses, part # CAM37262, has a threaded portion for connection to your RV sink that measures 1-3/4-inches in diameter at the threads. The overall diameter of the mounting flange is 2-5/8-inches. The linked photo shows these dimensions. view full answer...
The Camco RV Drain Trap part # CAM37262 that you referenced attaches directly to the sink. If would replace any style of trap that you have installed currently.
You could use a basket strainer with this as long as it would fit it's 1-3/4 inch diameter. view full answer...
The Valterra DWV Adapter for RV Sewer System # D50-2929 will fit with other 3 inch ABS threaded fittings. You will want to use Valterra ABS Solvent Cement - 1/4 Pint # A05-0303 to secure the end that is not threaded to the connected pipe. view full answer...
Yes, the "Y" part of the Valterra "Y" DWV Fitting # D50-2824 sits at a 45 degree angle. You could add a 45 degree elbow like part # D50-2892 and your pipes would be running parallel. view full answer...
We have the LaSalle Bristol Eccentric Tank Reducer # 34466V153 which can slide over your 1-1/2 inch diameter gray pipe to give you a 3 inch pipe that you could then attach the 3 inch pipe to 3 inch bayonet adapter part # T1028 and you'd be set. view full answer...
The diameter of the threaded portion of the # CAM37262 is 1-3/4 inches which is a very common size and hopefully what you need for your camper. view full answer...
The LaSalle Bristol RV Sewer Termination Adapter part # 34466V293B3 has a 3" hub fittings so it is designed to slide over a 3" outer diameter black sewer pipe and can then be fused on using the LaSalle Bristol ABS Solvent Cement part # 3447530889. If you're replacing a fitting then you will lose some length as you must cut the old fitting off in it's entirety.
If this was not the info you were looking for please just let me know and I'll do by best to assist. view full answer...
The closest match that we have is the Valterra # T1035-2 RV Sewer Elbow. The internal measurement on the spigot end is 3" and is meant for a glued connection rather than a push together connection with an o-ring. view full answer...
Yes you can use the Lippert Components Tote Tank Adapter # LC360789 to go from your bayonet connection to an end that works with the Camlock Connector # LC360578. view full answer...
The inner diameter of the Valterra Double Elbow DWV Fitting for RV Sewer System - 90-Degree - 3" Hub # D50-3047 is 3-1/2 inches. This will give you an outer diameter at the top of 3-7/8 inches. I've attached a video to help further.
You will want to use ABS solvent cement # A05-0303 to bond this fitting to your pipes. view full answer...
I think I'm following you. It sounds like your portable tote tank has a threaded fitting, but your sewer hose has a bayonet fitting like a typical sewer hose. If that is the case, then I have a solution for you, but we don't have a single adapter.
Instead, you will want to use fitting # T1029-2 and fitting # 344633703 to make the adapter you need. The non-threaded end of part # 344633703, will fit into the end opposite of the 3 bayonet lugs on part # T1029-2. You will want to use ABS... view full answer...
It seems like you're looking for a coupling like this one # F02-2104. It has two clamps and will go in between both your grey and black water tank and the rest of your waste system. view full answer...
You can definitely use the Valterra Bladex Waste Valve Body for RV Holding Tank # T1002VPM.
You're correct about the length not being a concern in regards to compatibility, what really matters is the 4-hole spacing, and for the Valterra # T1002VPM it is 2-7/8 inches, just like what you said you had.
With your measurements in regards to the extension, it sounds like you are saying you have a slip hub such as the Valterra RV Sewer Slip Hub with Flange - 2" # T1005-2 which has a 2-3/4"... view full answer...
Using PVC (white pipe) between ABS fittings (black) is not usually an optimal setup on a trailer because of the movement during transport and colder temperatures can cause PVC to break more easily.
The Oatey Purple is a PVC primer and not a glue so it wouldn't adhere correctly. Using a green transition glue as well as the purple primer on the PVC pipe could have worked however. Ideally they should have used black ABS pipe between the fittings and used ABS cement like LaSalle Bristol... view full answer...
It sounds like you are looking for the Valterra Eccentric Tank Reducer part # T1041-1 which installs in an RV gray water tank with with 3" diameter opening and then reduces this down to 1-1/2". The adapter will install inside the neck on the tank and then secured with gasket maker part # LT37467 and a band clamp part # H03-0009. In order to replace the waste valves you can then use the Double RV Waste Valves part # T80A depending on your setup. Please note, you'll also need the Valterra... view full answer...
The Projected Male Slip Fitting part # 372216-A-MS-A typically installs into the opening on the black water tank and then lets you attach a 3" diameter sewer pipe. view full answer...
We do have a different option than the Camco Y-connector you are referencing, which is the Camco RhinoFLEX RV Sewer Hose "Y" Fitting # CAM39812. While most people have favorable reviews for the RhinoFLEX, I have seen similar comments as yours that under pressure there can be slight leaks. So what I recommend using as a replacement is the Valterra Rotating "Y" Sewer Connector # F02-2030.
The Valterra is a heavier-duty connector than the Camco that has internal seals (see accompanying... view full answer...
I went out to our warehouse to measure the Valterra Hose Adapter w/ 3" Bayonet and Swivel Lug Fitting # F02-2029VP that you referenced. I found that the lug fitting has an overall diameter, at its widest point, of 4-1/4 inches (which includes the attachment nibs). The standard bayonet fitting has an overall outside diameter of 4-1/8 inches.
I have attached an image to assist.
If your storage compartment has an inside diameter of exactly 4 inches these likely won't fit too well.... view full answer...
The RV Reducing Y # T1014 has 3" lug to a 3" stationary flange and a 1-1/2" rotating flange. The relative position of the flanges is not critical and will fit most black and grey water tank connections. You might want to use # T1014-1 which has rotating flanges for both your black and grey water connections. Check out the videos linked below for more details on these products. view full answer...
If you are using the most common type dump hose out there, perhaps different in appearance but size wise, the same that almost everyone else at the camp site has, then yes. The EZ Coupler 4-in-1 RV Sewer Adapter with 90-Degree Elbow Fitting, # F02-3103 fits 3" slip and 3", 3-1/2", and 4" threaded sewer inlets. view full answer...
The outer diameter (O.D.) of the end opposite the flange on the Valterra RV Sewer Elbow part # T1035-2 measures 3-7/16" therefore if the inner diameter (I.D.) of the outlet on your black water tank is 3-7/16" then it will work for you. If not you would need to purchase an adapter at your local plumbing store. In order to attach the pipes I recommend using the Valterra ABS Solvent Cement part # A05-0303. view full answer...
We can offer steps on how to determine the correct black tank valve, though unfortunately isn't a way for us to know the exact valve that is on your Montana 5th wheel. To determine the right one is pretty easy, as you just need to know if the valve you are replacing slid over your pipe or into your pipe.
If both ends of your waste valve slid into your sewer pipe you will need the Valterra Bladex Waste Valve for RV Black Water Tank - 3" Spigot to 3" Spigot # T40A.
If both ends of your... view full answer...
It is unknown what that white material is. It is probably some kind of glue used by the manufacturer. We recommend the Valtera # A05-0303 Solvent Cement for these types of connections. Be sure to clean the joints before applying the cement.
view full answer...
If your 2017 Forester Class C has a female Cam style fitting on it the Lippert Components Tote Tank Adaptor # LC360789 will fit it as it has a male Cam style fitting. view full answer...
The LaSalle Bristol RV Sewer Slip Hub with Flange - 3" # 34466V13 you were looking at will work with the 3" ABS drain pipe on your RV.
The hub side will bolt to your black water waste valve that you mentioned.
You will also need the LaSalle Bristol ABS Solvent Cement # 3447530889 to secure the ABS pipe to the Slip Hub # 34466V13.
I included a video of the # 34466V13 for you to take a look at. view full answer...
There is Schedule 20 and 40 sewer pipe that has an outer diameter of 3-1/2 inches like what the Valterra Rotating Adapter for Rigid RV Sewer Pipe # T1028 is designed to work with so yes it would fit if the size was correct. view full answer...
The Camco RV Drain Trap, part # CAM37262 is designed for 3/4 inch diameter drain hoses.
The threaded inlet portion of the trap measures 1-3/4 inches at the threads. view full answer...
In most cases the Valterra Eccentric Tank Reducer - RV Gray Water - 3" Spigot to 1-1/2" Hub # T1041-1 is going to be attached to the gray water tank with an ABS solvent like # A05-0303, so it will need to be cut off in order to replace it. view full answer...
The threaded portion of the Camco RV Drain Trap, part # CAM37262 is 1-3/4 inches.
I called my contact at Camco and they told me the threads are 1-1/2 - 11.5 NPSL. My contact at Camco said the information came from the engineers and they were unable to tell me much about this size. The information I found online is that NPSL means National Pipe Straight Locknut, but I was not able to find more information about the 1-1/2-11.5.
view full answer...
The Valterra DWV Adapter for RV Sewer System, # D50-2929, installs into your RV's 3 inch waste valve system. If your tank hub is threaded as such, yes. Note that this is the internal diameter at 3". The outer threaded section is about 3-1/2". view full answer...
I contacted the manufacturer and the Valterra RV Sewer Termination Adapter, Item # T1029-2, fits standard ABS sewer pipes for RV uses. It is made from a very sturdy plastic and you would use something like ABS Solvent Cement, Item # A05-0303, to join the pieces. view full answer...
PVC Ptraps like the # D50-2215 do use a beveled cone washer when installing. When one of these leaks it can be just a matter of the nut not being tight enough or the washer needs replacing. view full answer...
The attached image was helpful in easily identifying exactly what measurement you wanting on the Valterra RV Sewer Elbow with Rotating Flange, # T1035-2. It is 5-5/16". view full answer...
The Camco RV Drain Trap part # CAM37262 is designed to screw onto the bottom of a sink and then ran outside the trailer with a drain hose similar to the Camco RV Drain Hose w/ Drain Trap and Evacuation Flange part # CAM37420. It is not really designed to be ran to a holding tank but if you were to do so then you would still need a p-trap like the Valterra P-Trap part # D50-2215 in order prevent the fumes for getting into the trailer. The only thing is I don't have any adapters to go from... view full answer...
The Valterra RV Sewer Spigot with Flange - 3" # T1006 will be compatible with LaSalle Bristol Valves. This has the standard mounting holes 3-3/4 inches apart on center. Then you will simply use the solvent cement like # A05-0303 or # 3447530889 to bond the spigot to your tubing view full answer...
I recommend using the Valterra Gray Water Drain Connector # T01-0091VP you mentioned. This has a 1-/1/2" FPT connector on one end, and a 3/4" MPT fitting on the other end to connect to a flushing hose like # W01-4300.
The # T01-0091VP keeps a low profile at 2-5/8" tall which should be small enough to fit in any space you need it. view full answer...
I have attached a list of all the sewer fittings we offer from LaSalle Bristol for you. I was not able to identify the specific fitting you inquired about but if you can send me a photo, I will try to see if we have the proper replacement for you. view full answer...
The fitting you are looking for is the EZ Coupler 4-in-1 Threaded RV Sewer Adapter with 90-Degree Elbow Fitting - Clear # F02-3112CL. This will allow you to connect your train hose and fits 3" slip and 3", 3-1/2", and 4" threaded sewer inlets at dump station. Internal seal helps prevent leakage and the clear plastic lets you see when the tanks are empty. view full answer...
The Camco RV Drain Trap # CAM37262 or # CAM37420 is designed to be used with a 1-1/2 inch - 11.5 threaded drain fitting. I recommend the Valterra Sink Drain with Strainer Basket # A01-2011VP or the LaSalle Bristol RV Drain with Strainer Basket - Metal - 1-1/2" Diameter # 34433JN1201 for this compatibility. view full answer...
The RV Sewer Slip Hub part # 34466V13 that you referenced has 3-3/4 inches between all of the mounting holes like you are looking for so it would work great. view full answer...
Yes the Valterra Hose Adapter w/ 3" Swivel Lug Fitting part # F02-2028VP will be a suitable replacement for your needs so long as your pipe coming out is 3" inside diameter. You will remove the old one clean up the end on the old pipe to ensure it is free of burrs and give it a light sanding. You then can use Valterra ABS Solvent Cement part # A05-0303 to make your connection with your new adapter. I've included a link to a video Conner was lucky enough to get to do here to show how the... view full answer...
It is challenging to know for certain if the Camco RV Drain Trap for 3/4" Diameter Drain Hose, # CAM37262 will help in this situation. I do see it as a cost effective attempt. I think best long term would be to reroute the drain lines to more aggressive angles with more direct flow to holding tank, if this is possible. I would attempt these routes before installing a pump.
view full answer...
For a permanent connection if you want the wye fitting you mentioned like the Double RV Waste Valves - Elbow - Rotating - 3" and 1.5" Hubs to 3" Spigot # T81 and then the Double RV Waste Valves - Elbow - Rotating - (2) 3" Spigots to 3" Hub # T85B. The actual manual handles will give you the manual shutoff you are seeking and they can be rotated so they don't come in contact with the other handles when installed together.
It is recommended to use PVC instead of hoses for as much length... view full answer...
The Camco RV Drain Trap # CAM37262 measures 3-3/4 inches tall which should help you determine the amount of clearance you need. Additionally, this trap is the same one that is on the Camco RV Drain Hose w/ Drain Trap and Evacuation Flange # CAM37420 you referenced (as there is not a CAM37430) so it will require the same amount of clearance.
I have added a link to a video review of the Drain Hose with Trap for you to take a look at. view full answer...
The URL's you posted for for the same item so I'm assuming you meant to reference the Camco RV Drain Trap for 3/4" Diameter Drain Hose # CAM37262 and the Exterior Evacuation Drain Trap # 37295195.
Both of these drain traps are exactly the same with a standard 3/4" MPT water hose connection and 1-3/4" standard strainer connection. The only difference between the two is just the brand.
view full answer...
The Valterra ABS Solvent Cement part # A05-0303 can be used in any temperature within reason. That said, the lower the temp the longer cure time it will require. The ideal temperature is 60 degrees Fahrenheit. There is no max or min temperature in the instructions. view full answer...
Though we do not carry either of those parts I can still help you out. What you are going to need - depending on how your hose threads - is either the RV Toilet Floor Flange # T05-0784, which has 3" diameter female pipe threads OR RV Toilet Floor Flange # T05-0782, which has 3" diameter male pipe threads. Additionally you will need the RV Toilet Floor Gasket with Hold Down Bolts # Q23653VP which is a universal design that works with the flange. view full answer...
The Valterra Coupling for Rigid RV Sewer Pipe # F02-2104 is designed for attaching 3 inch ABS style pipes. The larger end is for attaching to a schedule 40 style ABS pipe and the smaller end for attaching to a thin walled style pipe. When making this attachment you do need to use ABS solvent cement like the part # 3447530889. view full answer...
The big thing you need to determine is the diameter of the hose that feeds to your current sink trap. If it's 3/4 inch the part # CAM37262 would fit and work well.
I also attached a diagram that shows the opening dimensions as well for you to compare. view full answer...
The adapter you need is the Valterra part # T1041-1 that you referenced as it fits your configuration needs. The 3 inch portion fits into the tank and then the 1-1/2 inch portion fits over the elbow fitting like you need.
Rubber cement is basically not designed to be broken up though. view full answer...
Thank you for the photo of your RV's P-trap.
We offer one RV plumbing P-trap, Valterra RV Sewer P-Trap # D50-2215 that you referenced in your question, which is detailed in the linked photo. This part uses 1-1/2-inch fittings and installs using ABS Solvent cement # A05-0303.
For a larger size to replace yours you will probably want to check out a full-service plumbing supply store after measuring yours to confirm its size. view full answer...
I went out to the warehouse to measure Valterra RV Sewer Spigot with Flange - 1-1/2" Item # T1006-1 for you. The holes are spaced 2-7/16 inches apart on center up and down and side to side. Diagonally they are space 3-7/16 inches apart on center.
The outer diameter of the tube is 1-15/16 inches. The overall dimensions of the square part are 2-7/8 inches wide by 2-7/8 inches tall. view full answer...
To attach the Valterra Eccentric Tank Reducer # T1041-1 to the rest of the plumbing on the RV and prevent leaks use the Valterra ABS Solvent Cement # A05-0303. It was made for exactly this purpose! view full answer...
Since you are wanting the # T1011 with a 2 inch tee on the side instead you would want the part # T1012 as this is same configuration with the sizes you want. view full answer...
The Valterra Rotating Adapter for Rigid RV Sewer Pipe part # T1028 is designed to be welded to the end of a 3" ABS sewer pipe. However, if you don't want to permanently attach the sewer pipe to the hub fitting you could most likely just use a gasket maker like part # LT37467 to stop any leaks. view full answer...
You are not required to use any lubrication when installing the Valterra Coupling for Rigid RV Sewer Pipe # F02-2103 that you referenced. You'd just need to slip it over the ends of the pipe and then tighten the band clamps and you'd be set! view full answer...
Yes, the LaSalle Bristol RV Sewer Termination Adapter, # 34466V293B3S slides into your slip hub and glued in place using ABS solvent cement, # 3447530889.
The LaSalle Bristol RV Sewer Termination Adapter, # 34466V293B3 is also available for connecting your slip hub, fitting over sewer hose. Using the same ABS solvent cement, # 3447530889 view full answer...
I believe we do carry what you are looking for with the Lippert Components Tote Tank Adaptor # LC360789. This unit features a male CAM to female bayonet fitting and is three inches in diameter. I have also added a link to a video review of this connector for you to take a look at. view full answer...
For adding bayonet fittings to a sewer hose we have the Camco RV Sewer Hose Adapter part # CAM39543 which comes with the bayonet and the lug side fittings. This is designed to slip into a sewer hose though and we don't have anything that would normally glue over a PVC pipe. view full answer...
For what you are looking for the part # CAM39313 would be perfect.
This 4" x 3" sponge ring works with the gray-water seal or directly on an RV sewer hose for an odor proof connection to a dump station. view full answer...
When installing the # CAM37262 you need to unscrew the top half of the drain trap from the bottom half and screw it onto your 1-3/4" drain tightly and then you can attach the bottom portion back on to the top using two of the four mounting spots with the two screws provided to position the 3/4" drain hole in the direction you need it in. You can use some plumbers putty as extra protection but with the threads tight and the rubber gasket you should be fine. view full answer...
For the bayonet fitting on your valve, you can use the Valterra Rotating Adapter for Rigid RV Sewer Pipe - 3" Hub to 3" Bayonet - Black Plastic # T1028, the Valterra Adapter for RV Sewer Hose - 3" Bayonet Fitting - Straight - Black # T1024VP, or the Valterra Hose Adapter w/ 3" Swivel Bayonet Fitting - Black # T1024-2VP.
For the other side of that bayonet, you may be interested in the Valterra RV Sewer Lug Fitting with Flange - 3" # T1009, the Valterra RV Sewer Termination Adapter - 3"... view full answer...
The Valterra RV Sewer Slip Hub with Flange # T1005-1 can fit into a 2 inch pipe or over a 1-1/2 inch pipe. For a similar adapter that fits over a 2 inch pipe you'd want the part # T1005-2 instead. view full answer...
The Valterra RV Sewer Slip Hub with Flange - 1-1/2" # T1005-1 does not need a seal as well.
To install though you will need the Valterra ABS Solvent Cement # A05-0303. view full answer...
The LaSalle Bristol RV Sewer Slip Hub with Flange part # 34466V13 has an outer diameter of 3-3/16". That said, this adapter has a hub style connection which means it is designed so that a 3" diameter pipe can slide into the orifice. view full answer...
The LaSalle Bristol Coupling for RV Sewer System # 344633003 is designed to fit over a 3 inch pipe so it has a 3 inch inner diameter and the outer diameter is 3.5 inch. view full answer...
The Camco RV Drain Trap # CAM37262 comes with a 1-3/4" threaded inlet, so in order to use this drain trap with your 1-1/2" shower drain you need to use pipe tape # A05-0265 to provide a secure connection.
view full answer...
The Valterra DWV Adapter for RV Sewer System # D50-2922 does use the same 1-1/2 inch pipe thread size as what your Jabsco Macerator uses so it will match right up. And yes, it's okay to reduce the pipe size in the way you described as well. view full answer...
Yes, the outside diameter of the part # T1006-2 is 2-3/8 inches. For a version that has a 2-3/4 inch inner diameter you would want the part # T1005-2. view full answer...
Most likely the issue is related to the glue you used for your application. PVC and ABS require different glue types so you should verify that you used the correct glue for your application. If that's not the issue the problem is possibly the wrong size fitting. view full answer...
Go To Results