Will the M8 x 16.5mm T-Bolts Fit on the Rhino Rack Pioneer Platform

Question

Question:

Hi. Item # RR72XB Will these rectangular washers fit in slots of my Rhino Platform? Or is there a simular kit that will? Thanks

asked by: Paul K

1

Helpful Expert Reply:

Yes. The Replacement M8 x 16.5 mm Stainless Steel Rectangular T-Bolts for Rhino-Rack Accessories - Qty 4
# RR72XB will fit in the t-slot channels on the Pioneer platforms.

expert reply by: Erik B

1

Answer 1

Hey Michael, I did some digging and I believe you are looking for a replacement M8 T-bolt which we have as the part #RR65XB.

view full answer...

Answer 2

I talked with my contact at Rhino-Rack about fitting the Rhino-Rack Pioneer Platform Rack - Raised Side Rails - 60" Long x 54" Wide #RR86AB onto your 2013 Ford Explorer. When attaching the platform rack onto your factory rails, you want to…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 9

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Will the M8 x 16.5mm T-Bolts Fit on the Rhino Rack Pioneer Platform

Product Page this Question was Asked From

Continue Researching