Do the TorkLift StableLoads for Upper Overload Springs for a 2009 Ford F150 Require Drilling

Question

Question:

Looking for instructions. To have my springs predrilled after I buy the new set and befor I put them on

asked by: John M

0

Expert Reply:

I checked with Torklift and the TorkLift StableLoad Suspension Upgrade for Upper Overload Springs part # TLA7200 which is a fit for a 2008 Ford F-150 features a no-drill application but does require the factory installed upper overload.

I have attached a snip from the instructions below.

expert reply by: Conner L

0

StableLoad 7200 Instructions
(click to enlarge)

Answer 1

The difference between the upper and lower Stableloads is the vehicle setup and because of that you can't install both at same time. The upper StableLoad like the part #TLA7200 is for versions of the 2021 Ford F-350 that have upper overload…

view full answer...

Answer 2

From the looks of the photo you have attached it appears you have a lower overload spring, not an upper overload spring that is required for the TorkLift StableLoad Suspension Upgrade for Upper Overload Springs part #TLA7200 to work. This kit will…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 5

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Hey Douglas! The correct Gen-Y gooseneck pin box for your 2022 Forest River Cardinal Red is the #GY33GR. This fits the Rhino bolt pattern and is rated for trailers with a GVWR of 7,275-16,360 lbs. You will also need safety chains #GY49GR to complete…

view full answer...

Answer 12

Hello Matt, I was seeing some mixed information on this as well, so I reached out directly to my contact at Firestone to confirm. The Firestone Ride-Rite Air Bags w/ Easy Mount Compressor - Wireless Control - Single Path - 5,000 lbs #F44XV will fit…

view full answer...

Do the TorkLift StableLoads for Upper Overload Springs for a 2009 Ford F150 Require Drilling

Product Page this Question was Asked From

Continue Researching