Best Replacement For Jensen MP5000 RV Radio

Question

Question:

I’m looking for a direct replacement plug n play stereo for my camper. I’ve got a 2009 Sprinter by Keystone my stereo is a Jensen MP5000. Thanks for your time.

asked by: Jimbo W

0

Expert Reply:

We do have a good replacement that will be about the same size as your Jensen MP5000 but there are no plug and play replacement options. That being said, the Jensen # JWM60A radio is going to be the best replacement you can find for your current radio. Just match up the functions of the wires using these heat shrink connectors # DW05743-10 if your current plug will not hook into the # JWM60A radio.

expert reply by: Adam E

0

Answer 1

The "Amp Remote" blue wire coming from the harness for your Jensen RV Stereo #JWM60A is only used if you are needing to power an external amp. If you have an external amp you would would run this wire to it, which basically tells the amp…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 9

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

Good question, Dave. The easiest way is to match the RVpaws kit to your jack leg or leveling system. For example, there are specific kits for the brands and lineups out there: Standard 2" round jack leg = #RV57FR Standard 2" square jack leg…

view full answer...

Best Replacement For Jensen MP5000 RV Radio

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching