Dimensions Of Flexco Manual Pull-Out Step For RVs SMFP-1100

Question

Question:

What is the vertical distance between the support rod and the upper brackets

asked by: Allen A

0

Expert Reply:

I had our warehouse measure the Flexco Manual Pull-Out Step for RVs # SMFP-1100 and from the center support to the top of the mounting bracket measure 3-5/16" as shown in the included diagram.

I also included a few other diagrams with other dimensions for you to take a look at.

expert reply by: Samuel C

0

click to enlarge

Answer 1

I looked up a couple pictures of your 2014 Coachman Clipper 17BH and it appears to have the Manual Pull Out Step which is a pretty standard step like #SMFP-1100. Like most single steps this has a narrower mounting bracket width than double or triple…

view full answer...

Answer 2

view full answer...

Answer 3

I looked up pictures of your 2001 Winnebago Minnie Winnie 22R and it has a cut out for a single step below the door. The Flexco Manual Pull Out step part #SMFP-1100 was designed to fit RV setups just like yours but you'd want to measure first to…

view full answer...

Answer 4

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 5

Hey Donny! For your Dometic Penguin/Brisk Air 15,000 BTU AC model B59516.711C0-MX, the correct soft start is the #DMC93JF. This is designed for Dometic Brisk II electronic air conditioner units with in-wall thermostats.

view full answer...

Answer 6

Appreciate you reaching out Juan! Lippert confirmed that your LCI number is a 1621 pin box. Rota-Flex 5th Wheel Pin Box #LC328330 is going to be a direct replacement and bolts right on. The Rota-Flex pin box is highly rated because it has a pivoting…

view full answer...

Answer 7

Hi William! The Active Controls ActiveStart Plug-In Soft Start for RVs - 50 amp #AS54FR will plug into a campsite pedestal and offer dual soft start circuits, but this one does not have surge protection. This is meant to be paired with a custom surge…

view full answer...

Answer 8

Hello Douglas, Thanks for writing in, and thank you for your order! I am sorry to report that the manufacturer does not have a weld pattern or installation instructions available for the Sleeve-Lock A-Frame Trailer Coupler #CA-5296-B. I know that…

view full answer...

Answer 9

From the center line to center line of the brackets for the Solera 12V XL Power RV Awning - 16' Wide - Extra-Long 9'8" Projection - White Fade #LCV000334965-362241 it measures 16' as you can see in the attached photo. When I reached…

view full answer...

Answer 10

The 2019 Ford F-150 trailer wiring DOES NOT like trailers with LED taillights or lightbars that attach to the vehicle and use trailer wiring for activation. This is a problem we saw first with German vehicles a while back and an adapter was made to…

view full answer...

Answer 11

Hello Jason, thanks for reaching out. Yes, the Kenda Karrier KR53 ST205/75R15 tire with 15" black aluminum wheel #KE58JV does come balanced from the factory. Trailer tire and wheel assemblies are balanced by matching the tire’s high and low…

view full answer...

Answer 12

Hey Steve. Normally I would say you're describing a bad ground but we've had this issue with the wiring connectors before when Toyota first launched the Grand Highlanders. Does your 2025 Grand Highlander have the factory tow package?…

view full answer...

Dimensions Of Flexco Manual Pull-Out Step For RVs SMFP-1100

Product Page this Question was Asked From

Continue Researching