Replacement Trailer Connector with 7-Way and 4-Way for 2012 Chevy Silverado Bumper Fit

Question

Question:

I have a 2012 Chevy Silverado LT. It has the OEM 7 pin round trailer socket in the rear bumper. The newer models have a combo 4 and 7 pin socket. Is there a combo socket that can replace my existing pin socket in the same place in the bumper? I know their are some that will plug into the OEM harness but all seem to come with a bracket for mounting under the the bumper. I dont want to do that in case I have to back into deeper water to launch my boat. Thanks for the help.

asked by: Bradford M

0

Expert Reply:

The Hopkins Endurance Multi-Tow Twist-Mount 7-Way RV and 4-Way Flat Trailer Connector - Vehicle End # HM40920 will fit the location and give you the functions you are seeking. It will work well for your 2012 Chevy Silverado LT.

expert reply by: Jason S

0

Answer 1

In order to replace the rusted trailer connector mounting bracket on the trailer hitch for your 2007 Chevrolet Avalanche I recommend using part #18144 if you have a 4-way or part #18138 if you have a 7-way. These brackets will attach to the hitch via…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 10

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 11

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 12

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Replacement Trailer Connector with 7-Way and 4-Way for 2012 Chevy Silverado Bumper Fit

Featured Help Information

Miscellaneous Media

Continue Researching