Long 2-Wire Pigtail Recommendation

Question

Question:

Do you have a two wire pigtail that is 24inch or more in length? My clearance lights will be on the side of a flat bed trailer and the rail along which the main electric cable runs will be much more than 6foot from the lights. I can certainly extend the length but would be much easier with longer pigtails.

asked by: Gerry

0

Expert Reply:

Check out the Two-Wire Straight Pigtail # A46P75B, this 2-wire pig tail is 75 inches. Since you said you need much more than 6 feet this may not be quite long enough at 6.25 feet long, but it is the longest one we offer.

expert reply by: Jameson C

0

Answer 1

Hey Marc, the difference between the two grease seals is that the part #34823 is sold individually and the part #RG06-010 is sold in pairs. Aside from that they are the exact same seal. How many seals are you in need of?

view full answer...

Answer 2

I wasn't able to find anything in regard to a replacement part for your TDE 11029C hub assembly, but if you can pull your hub and either look for bearing/grease seal parts numbers or measure the different locations on your spindle then I can see…

view full answer...

Answer 3

The 125255UC seal has a 1.249" ID and a 1.983" OD and for that our part #34823 will be the correct replacement.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Long 2-Wire Pigtail Recommendation

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching