Spacers for Timbren Suspension Enhancement on 2020 Ford F-250 Super Duty

Question

Question:

I have a 2020 F250 Tremor and the measurement from the bottom of the frame to the top of the plate that the joust bumper would make contact with is 8 1/2 inches and leaves 1 5/8 inch space. So if my math is correct this product will only reduce my rear sag by about 1/2 inch which doesnt amount to much. Currently the rear of my truck sags about 2 inches when towing my fifth wheel camper. Can I use the kit made for the 350 which comes with a spacer?

asked by: Tony M

0

Expert Reply:

It is possible you can use the Timbren Suspension Enhancement System # TFR350SDJ (which is made for a Ford F-350) on your 2020 Ford F-250, but we have never done this and it hasn't been tested so I just can't guarantee a good fit.

There are spacers that will work with your F-250 and the Timbrens that are designed to fit it, the Timbren Suspension Enhancement System # TFR250SDJ.

You can add spacers in increments or 1/2" or 1" with the Timbren 1/2" Spacer # TA25722-90P00 and Timbren 1" Spacer # A25723-90AH00.

expert reply by: Kyle S

0

Answer 1

Yep, it sure does; the Timbren suspension enhancement you asked about is a fit for your 2022 Ford F-350 Tremor. The correct part number is the following: - Timbren Suspension Enhancement System #TFR350SDJ The Timbren #TFR350SDJ are a really smart…

view full answer...

Answer 2

All of the air spring kits for the 2011 Ford F-250 mount to the sides of the truck frame rails. The issue is that the B&W gooseneck hitch brackets also install in the same location but on the outsides of the frame rails. This would not be a…

view full answer...

Answer 3

There are two Timbren kits that fit your 2020 Ford F-250 we have the #TFR250SDJ which has an 8,600 pound capacity and fits 2- and 4-wheel drive models. And second we have #TFRTT350J which is rated for 8,000 pounds and also fits 2- and 4-wheel drive…

view full answer...

Answer 4

We only carry the springs for those heavy duty style ramps. For the springs we have the Ramp Spring - 2K Torque for 1-1/2" Shaft - left hand #RS16933LH and corresponding right hand #RS16933RH. The other parts will need to be either straightened…

view full answer...

Answer 5

Hey Micah! Pacbrake has actually been around for a long time, more than 60 years. We have had customers ask for these air bags in the past, and we've seen them on vehicles coming in. Until now, Firestone has been the go to since their quality is…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

Thanks for the picture! I checked with Progressive Dynamics the replacement power converter you need for your Parallax Series 7300 Model 7345 is the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers - 45 Amp item #PD4645V.

view full answer...

Spacers for Timbren Suspension Enhancement on 2020 Ford F-250 Super Duty

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching