Actual Diameter of Kodiak Disc Brake Kit for 3,500 Lb Axles

Question

Question:

What is the actual rotor diameter? I see 10” in the description but mine have the the same calipers but are closer to 10 7/8”.

asked by: Justin M

0

Expert Reply:

The Kodiak Disc Brake Kit part # K2R35D comes with rotors which measure 10-7/8" diameter but are commonly just referred to as 10" diameter rotors.

expert reply by: Conner L

0

click to enlarge

Answer 1

To find your exact hubs we will need either the numbers off the bearings and grease seals to determine the spindle size or the diameter of the different landings on the spindle. I would also need to know the bolt pattern used for your hubs.

view full answer...

Answer 2

The slip-on rotor included with the Kodiak #K2R35D disc brake kit have an inside diameter of 6.681 inches and an outside diameter of 10.875 inches, as shown in the provided photo. The rotors are compatible with hubs that have a 5 on 4-1/2 inch bolt…

view full answer...

Answer 3

We don't have the ability to know exactly what your trailer would require in terms of braking components or a replacement axle. You'd need to check out the axle to determine it's capacity for the braking components but due to age it may…

view full answer...

Answer 4

Finding information on the Tie Down 46250 was not an easy task as it was discontinued awhile back. From what I could find, it looks like the calipers marked 46250 often times have to change the mounting bracket and rotor/hub in addition to the…

view full answer...

Answer 5

There is no way for us to know what brakes are needed on any specific trailer, but we can tell you how to figure out what you need. For both you need to have a brake flange and to know your axle capacity, but starting with drum brakes you also need…

view full answer...

Answer 6

In the answer page you're referring to Conner didn't say the hub face to brake flange is useless. He said measuring from brake flange to brake flange (from one side to the other) isn't really helpful when choosing a replacement axle. The…

view full answer...

Answer 7

Appreciate the photos, they were great, and you are 100 percent right that the correct disc brake kit for you is the 3,500 lb kit from Kodiak: - Kodiak Disc Brake Kit - 10" Rotor - 5 on 4-1/2 - Dacromet #K2R35D The #K2R35D have the right size…

view full answer...

Answer 8

As long as that is a 3,500 lb axle with a 4-bolt brake flange on your EZ Loader boat trailer you will be able to use the DeeMaxx Disc Brake Kit #DE42FR. The slip-on rotors will fit over the 5 on 4-1/2 bolt pattern on your existing hubs without any…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Actual Diameter of Kodiak Disc Brake Kit for 3,500 Lb Axles

Product Page this Question was Asked From

Continue Researching