Does this Replacement Lithium Converter # PD4590LICSV Work with Progressive Dynamics Power Center?

Question

Question:

I need to know if this part will work for PD4590K18L on a 2015 vengeance reeper?

asked by: Erica M

0

Expert Reply:

Yes, the Replacement Lithium Converter # PD4590LICSV will work for your PD4590K18L. I checked with Power Dynamics to make sure that the difference between your part and the # PD4590K18LS8 would still allow for use with the Lithium Converter, and they confirmed that is the case.

expert reply by: John R

0

Answer 1

The Progressive Dynamics #PD4590CSV is designed as a replacement for the Progressive Dynamics RV Power Control Center #PD4590K18LS8. It is not made as a replacement for the WFCO 9990, and unfortunately we do not offer a converter section that will be…

view full answer...

Answer 2

Hey Jeff, thanks for reaching out! Yes, the Progressive Dynamics 4500 Series RV Converter w/ Charge Wizard #PD4560K18LS8 is compatible with lithium batteries. All you have to do is swap the jumper over to the "LI" side (see attached photo)…

view full answer...

Answer 3

The correct replacement converter section for your 90 amp 4500 series Progressive Dynamics panel that is compatible with Lithium batteries is the part #PD4590CSV.

view full answer...

Answer 4

The Progressive Dynamics RV Power Control Center with AC/DC Panel and Converter/Smart Charger - 90 Amp #PD4590K18LS8 is a distribution panel for your AC and DC appliances which will also charge your battery when hooked up to shore power. It is not an…

view full answer...

Answer 5

I spoke to Progressive Dynamics, the Progressive Dynamics REL 90A 4500 Series Inteli-Power Converter Section part #PD4590CSV is a fit for you 4590 panel. You have an older style panel which uses a different fan layout but the above will fit and is…

view full answer...

Answer 6

Hey John, it's good to hear from you again! When switching over to the Progressive Dynamics 4500 Series RV Converter w/ Charge Wizard and AC/DC Distribution Panel #PD4560K18LS8, you'll need to remove your breakers, the bus bar, and your fuses…

view full answer...

Answer 7

The Charge Wizard button on your Progressive Dynamics PD4560, replaced by the part #PD4560K18LS8, is only designed to be used for lead/acid batteries. This mode is supposed to be turned off when connected to lithium batteries so there is constant…

view full answer...

Answer 8

Hey Greg, so Lithium batteries do require special converters since they charge at a higher voltage. The Progressive Dynamics part #PD4560K18LS8 is lithium compatible and can put out up to 60 amps so it would do a great job keeping your battery bank…

view full answer...

Answer 9

To replace just the converter section of your PD4590 series power center you'll need part #PD4590CSV. This is a direct factory replacement for a 90 amp PD4500-series power center, like you have.

view full answer...

Answer 10

Hello Mike, I am curious on what kind of batteries you are trying to charge, if they are Lithium batteries that would explain why it is not working. If you have lead-acid batteries (flooded or AGM) I would just swap out the converter section with the…

view full answer...

Answer 11

I am not 100% sure what you are asking. The newer models of the power centers/converter sections like the Progressive Dynamics 4500 Series RV Converter #PD4590K18LS8 are coming with the switch that you are referencing that allows you to switch…

view full answer...

Answer 12

The recommended lug nut torque for your 7,000lb axle depends on a few factors like wheel size, stud size etc. Check out the attached photo which shows the torque specs for a variety of applications. I see you were looking at the Dexter Nev-R-Adjust…

view full answer...

Does this Replacement Lithium Converter # PD4590LICSV Work with Progressive Dynamics Power Center?

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching