Remove Thule Camber Cradle Strap Install Video

Question

Question:

Can you help on how to remove the cradle strap from a thule camber to replace it? thanks

asked by: Matt F

0

Expert Reply:

We actually did a video for the replacement straps that fit the Thule Camber part # TH9056 that you referenced with part # TH536. Check out the link on this page to see the entire process walked through.

expert reply by: Jameson C

0

Answer 1

The good news is the Thule Helium Aero 2 Bike Rack, part #TH9042PRO, comes with a built-in, anti-rattle locking hitch pin so you will not need to purchase a separate locking hitch pin. Check out the video review of the Helium Aero 2 (see link) which…

view full answer...

Answer 2

The cradle ratchet straps for your Thule Apex XT Bike Rack like #TH9024XT should remove just as they were installed. It might take some force to pull the strap completely out of the cradle because of its ratchet design but this is the only way to…

view full answer...

Answer 3

You will need the Thule Universal Change Key, part #853-1251, in order to remove your existing factory lock cores. With your existing locks in the unlocked position insert the universal control key to remove the core. It may be necessary to wiggle…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Remove Thule Camber Cradle Strap Install Video

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching