What is the Difference Between Polypopylene Cover and PolyPro III Trailer Covers

Question

Question:

What is the quality difference between this cover and the CA80038?

asked by: Shawn

0

Expert Reply:

The Adco Polypropylene RV Cover for Pop-Up Camper - Up to 10' Long - Gray # 290-2891 is the economical model of cover. It is a single layer of breathable yet water repellent polypropylene.

Cover # CA80038 is a premium cover that uses a triple-ply (PolyPro III) fabric that not only keeps the trailer dry but also protects against nicks and scratches. This is the ideal cover for climates that have frequent precipitation. I have included some instruction links for you.

expert reply by: Michael H

0

Answer 1

The 24 inches is correct but make sure you are measuring in the correct place. You will measure diagonally from the center of the ball cavity on the trailer coupler back 24 inches along the trailer frame. This is where the center of the ball on the…

view full answer...

Answer 2

The Greystone Standard RV Microwave w/ Trim Kit - 1,350 Watts - 0.9 Cu Ft - Black #324-000105 will measure 19" wide, by 14-1/4" deep, by 13-1/2" tall without the trim installed. The height measurement is indeed from the absolute top to…

view full answer...

Answer 3

For the dual friction you are looking for, I recommend adding the Reese Friction Sway Control Kit - Economy - by Draw-Tite, Reese and Hidden Hitch #83660 to your hitch ball. This adjustable friction sway bar can be added using the Reese Sway-Control…

view full answer...

Answer 4

All of our friction sway control unit

view full answer...

Answer 5

The Reese Friction Sway Control Kit #83660 referenced in your question can indeed be installed on the left/driver side of the trailer. To do this you just need to remove the slide bar and reinstall it upside down like you mentioned. This is…

view full answer...

Answer 6

The center of the ball on the plate that mounts on the trailer should be 24 inches from the center of the trailer coupler (where the center of the hitch ball would be when towing). The first two diagrams on the top of page 2 in the instructions (see…

view full answer...

Answer 7

If you are backing up mainly in a straight line you can leave the Reese Friction Sway Control part #83660 installed but if you end up getting into a tight enough turn you'd need to disconnect the kit.

view full answer...

Answer 8

I can absolutely understand not wanting to take your hub apart to find the right replacement hub, but unfortunately that is the only option as the numbers you referenced are not any type of indicator of a replacement. So, to determine the correct hub…

view full answer...

Answer 9

Sway control is designed to be used in situations where the trailer sways under adverse conditions such as high winds or when large vehicles are passing causing the trailer to become unstable. Sway control also helps if you have to maneuver suddenly.…

view full answer...

Answer 10

Due to the age of your 96' Coleman pop up and there being a few different versions it's hard to say exactly what size you have, but we did have a guy with a 97' come tell us he had the tire size 5.30-12 mounted on 5 lug wheels so I'll…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

What is the Difference Between Polypopylene Cover and PolyPro III Trailer Covers

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching