Replacement Key for UWS Toolbox Latch

Question

Question:

Have a toolbox referenced above need replacement keys. Need to know which ones to purchase if you can help. Thank you in advance Uws tbs-60-sl toolbox replacement key needed

asked by: Lisa B

0

Expert Reply:

On your UWS toolbox the number for the replacement key you need is printed on the lock cylinder. For example, the part # KEYCH509 is a replacement key made specifically for the UWS Toolboxes that use key code 509. This is the correct replacement key for your UWS toolbox.

The KEYCH--- is the way to find your specific key number with the dashes being the number printed on the lock core. I tried to see the number in the photos and can only make out a 5.

If you can't make out the number in person, then you will need to drill it out and use a replacement lock like the Replacement Lock Cylinder for UWS Toolboxes w Square Paddle Handles - CH509 # UWSLOCKCH509.

expert reply by: Jason S

0

click to enlarge

Answer 1

This is a common issue for installing a brake controller in the 2019 Ford F-150 and the easy solution is to install the part #BRK-ELECKIT which bypasses the very mysterious brake controller power wire issue your truck has and allows your brake…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Replacement Key for UWS Toolbox Latch

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching