Comparing Curt Hitch C25VR and U-Hual Hitch CMF13448

Question

Question:

Is u-hauls CMF13448 the same as C25VR?

asked by: Lori

0

Expert Reply:

The Curt Trailer Hitch Receiver part # C25VR is the same as a U-Hual Trailer Hitch Receiver part CMF13448 and they are both fits for a 2020 Subaru Ascent.

expert reply by: Conner L

0

Answer 1

Hello Peter, thanks for reaching out. The Draw-Tite Trailer Hitch Receiver #DT76PR weighs 36 lbs. Sadly we do not have any videos of this hitch being installed. I do have a video of the Curt #C25VR being installed which is also for the 2024 Subaru…

view full answer...

Answer 2

Hey Mark we do have a hardware kit for the 13570 Curt Trailer Hitch our item #C69VV. It is the Replacement Hardware Kit for Trailer Hitches item #RHK. This kit has the carriage bolts, square-hole spacers, serrated-flange nuts, flat washers, and…

view full answer...

Answer 3

We have just what you need. If you type RHK in the search box on our website it will take you to the replacement hardware kit product page. You will then simply type the number of the hitch you need hardware for in the box that is labeled Hitch Item…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 8

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 9

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Comparing Curt Hitch C25VR and U-Hual Hitch CMF13448

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching