Galvanized Spare Wheel and Tire for PWC Trailer with Tire Size ST175/80R13

Question

Question:

I need a recommended tire and galvanized wheel. Triton PWC Dual place, single axel trailer. 2019 Triton Elite WCII ST175/80r13 6ply Thank you.

asked by: Robert

0

Expert Reply:

For what you are looking for we have the part # AM3S160 which is the tire size ST175/80R13 mounted on a galvanized wheel with a 5 lug bolt pattern like you are looking for. The ply rating is also 6 as well.

expert reply by: Jameson C

0

Answer 1

The pilot diameter on a wheel, like the one with part #AM30620, is the diameter of the bigger hole that is directly in the middle of the wheel. The pilot hole diameter of the wheel for the part I just measured is 2.84". I have attached a picture…

view full answer...

Answer 2

The pilot diameter is measured as the diameter of the large hole in the center of the wheel. The Dexstar #AM20790 steel dual trailer wheel you referenced has a 4.88 pilot diameter. So which pilot diameter would you need? To figure that out, I would…

view full answer...

Answer 3

Hey Steve, I can't seem to find anything with that pattern that didn't come up as a damaged wheel where the bolt holes were damaged, throwing off the measurement. Are the bolt holes on your wheel worn/oblong? With you being at 4-7/8"…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Galvanized Spare Wheel and Tire for PWC Trailer with Tire Size ST175/80R13

Product Page this Question was Asked From

Continue Researching