Replacement Lug Studs for Al-Ko 8500 Hub and Drum on 2012 Keystone Hideout 19FLB

Question

Question:

Any ideas on a replacement wheel stud? I have AL-KO 8500 hubs. I’m pretty sure it is a 1/2” thread by 2” long stud. Any help would be appreciated. Thanks

asked by: Paul B

0

Expert Reply:

We don't have a database that tells us what the stud size is on that hub, but I was able to do a little bit of research and find some reports that say that your 1/2" thread by 2" long stud seems to be accurate. For that size wheel stud you can use the Redline # 7-122 lug studs you were looking at which are 2" long and have 1/2" threads.

expert reply by: Erik B

0

Answer 1

Hey Javier. For a 6" long suspension bolt, you'll want the Spring-Eye Bolt for Slipper Springs item #7-170. This grade 5 bolt is sold individually and measures 1-1/8" x 6". The matching lock nut is sold separately it is the Locknut…

view full answer...

Answer 2

The diameter of the 1/2" Kodiak Wheel Bolt #K12WB2 is 0.70" according to my contact at Kodiak.

view full answer...

Answer 3

Looks like you have a spline diameter of .56 inches and and threaded portion of 1/2 inch which is very popular. For that you'd want the part #K12WB2. I attached a picture that has a dimensional diagram for you to check out as well.

view full answer...

Answer 4

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 5

For a 3,500 lb hub/drum replacement that will work well to replace your AL-KO 8500 you'd want the hub part #84546UC3-EZ which fits the spindle and has the 5 on 4-1/2 inch bolt pattern you need. For brake assemblies then the Electric Brake…

view full answer...

Answer 6

What diameter knurl do you need? I was not able to look up that info since we don't carry the TDE brand.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Replacement Lug Studs for Al-Ko 8500 Hub and Drum on 2012 Keystone Hideout 19FLB

Product Page this Question was Asked From

Continue Researching