Recommended 6" Long Suspension Bolt and Locknut

Question

Question:

Looking for 2 Equalizer Suspension Bolt with Locknut - 6” Long for cam súper line tilt trailer tank you

asked by: Javier S

0

Expert Reply:

Hey Javier. For a 6" long suspension bolt, you'll want the Spring-Eye Bolt for Slipper Springs item # 7-170. This grade 5 bolt is sold individually and measures 1-1/8" x 6".

The matching lock nut is sold separately it is the Locknut for Suspension Spring-Eye Bolts - 1-1/8" Diameter - Zinc Plated item # 6-72. It is also sold individually.

What do you haul on your tilt bed trailer?

expert reply by: Jerred H

0

Answer 1

Hey Donald, thanks for the information and welcome back! I checked with Optronics and there is no replacement lens or the part that covers the side available for their ONE LED Trailer Tail Light item #STL0066RBG. The only option available is to…

view full answer...

Answer 2

Hey Bruce, what you have is a 3,500 lb AL KO axle so for a replacement hub/drum you would need the part #AKHD-545-35-EZ-K and then for replacement brake assemblies you'd want the part #AKEBRK-35-SA and you'd be set. These are self adjusting…

view full answer...

Answer 3

I went out to the warehouse to take some measurements of Curt trailer hitch #C14082. I made a picture showing the measurements for you. The bolt holes, starting from the one furthest forward on the vehicle, measures 2-3/4 inches to the center of the…

view full answer...

Answer 4

We don't have a database that tells us what the stud size is on that hub, but I was able to do a little bit of research and find some reports that say that your 1/2" thread by 2" long stud seems to be accurate. For that size wheel stud…

view full answer...

Answer 5

For a 3,500 lb hub/drum replacement that will work well to replace your AL-KO 8500 you'd want the hub part #84546UC3-EZ which fits the spindle and has the 5 on 4-1/2 inch bolt pattern you need. For brake assemblies then the Electric Brake…

view full answer...

Answer 6

Hey Mathieu, since you have an Al Ko 3500 lb trailer axle with a 5 on 4-1/2 inch bolt pattern the correct replacement hub/drum would be the part #AKHD-545-35-K which happens to be pre-greased so it's ready to install.

view full answer...

Answer 7

It looks like Trailer Hub and Drum Assembly - 5,200-lb Axles - 6 on 5-1/2 Item #8-201-5UC3 could be the right replacement for you. You can check the bearing numbers if you still have the bearings. If they are 25580 for the inner and LM67048 then this…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Recommended 6" Long Suspension Bolt and Locknut

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching