Replacement Knob Needed for Pressed Threaded Bolt on Reese Outfitter Bike Rack

Question

Question:

I have a Reese Outfitter Bike Rack. I need to replace a knob. The 1/2 in. thread bolt is press fitted into the rack and the female knob screws on. See pictures. Do you carry these knobs.

asked by: Richard

0

Expert Reply:

Unfortunately that rack has been discontinued and we don't have replacement parts. You can simply use 1/2 inch 13 thread standard hardware nuts like # CE10812 or # 55178 to secure the plate.

expert reply by: Jason S

0

click to enlarge

Answer 1

In order to install Curt trailer hitch #C15800 on your 2012 Dodge Ram 4500 cab and chassis model you will have to drill into the frame because, like you have said, there are no holes in the frame already. The rivet that is in the rear most part of…

view full answer...

Answer 2

We only have the nut and washer sold with the hitch ball like the B&W #BWHB94006. This gooseneck ball has a shank 1-1/2" in diameter by 2-3/4" long.

view full answer...

Answer 3

For a hitch with a shorter distance between the mounting flanges down to the hitch opening that is confirmed to fit your 2014 Chevy Silverado you would want the B and W hitch #BWHDRH25601 over the Curt Hitch part #C15800. This hitch has slightly…

view full answer...

Answer 4

I spoke to my contact at Swagman and she informed me that in order to install the Replacement Knob #P1004 that you referenced you will need to put the metal lock washer on first and then the other two plastic washers before you install it on the…

view full answer...

Answer 5

I believe the part you are looking for is Swagman Hitch Mounted Bike Rack Replacement Knob, part #P1004. We carry them and I have added a link below.

view full answer...

Answer 6

You'll need one of the following knobs based on when your Swagman Original Bike Rack, part #S64152-2 was made: Prior to 2009, part #P1004, this includes a standard 2 inch bolt that will fit the knob. 2009 to Present, part #P1041, which is…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

Hey Kelvin, welcome back. To flat tow a 2026 Ford Maverick with your Demco Commander II Tow Bar item #DM9511012, I recommend the following parts: Baseplate Kit - Demco Tabless Base Plate Kit item #DM38CV Wiring Harness - Roadmaster Diode 7-Wire to…

view full answer...

Answer 12

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Replacement Knob Needed for Pressed Threaded Bolt on Reese Outfitter Bike Rack

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching