Will the Ram Gooseneck to 5th Wheel Trailer Coupler Adapter Inner Tube Work On a Semi

Question

Question:

Does this kink pin fits in semi truck thanks

asked by: Benny

0

Expert Reply:

The Ram Gooseneck to 5th Wheel Trailer Coupler Adapter Inner Tube part # KPG5-Q30IP and Gooseneck to 5th Wheel Trailer Coupler Adapter part # KPG5-R25-IP both have an industry standard 2" diameter kin pin which most semis use so yes it will work.

expert reply by: Conner L

0

Answer 1

I contacted the manufacturer on your behalf regarding your question. Per Ram, the plate is the same 10"x10" size on the #KPG5-R25-IP and the #KPG5-R30IP. Our review video also had it measured the same. The capacity difference increase for…

view full answer...

Answer 2

If the fifth wheel hitch is mounted using industry-standard 5th wheel rails (see photo), you can simply remove the existing fifth wheel, and mount an adapter like #16055. If your gooseneck trailer has a removable coupler, we offer some king pins that…

view full answer...

Answer 3

The tube of the Gooseneck to 5th Wheel Trailer Coupler Adapter #KPG5-R25-IP sits perpendicular to the square plate towards the bottom of it as depicted in the attached picture. The holes are perpendicular (at a 90 degree angle) as well.

view full answer...

Answer 4

The Ram Gooseneck to 5th Wheel Trailer Coupler Adapter Inner Tube - Square - 30,000 lbs #KPG5-Q30IP is a 4 inch square tube with a 7/8 inch pin hole diameter. The holes are 2-11/16 inches on center and have a total adjustment height of 8 inches. The…

view full answer...

Answer 5

The overall height of the coupler tube part #KPG5-R25-IP is 23-7/16 inches.

view full answer...

Answer 6

Either way is correct. It depends on if you want to keep the semi-style 7-Way (if you need to tow that type of trailer) or if you will never be towing a semi-trailer. If you need to keep the 7-Way semi active on the truck, then you would need to make…

view full answer...

Answer 7

If you want to use a brake controller that does not require the use of the air brakes on your Mack Truck, then you can use an electric brake controller like #90195. You will have to hardwire it to the vehicle and you will need a 7-Way trailer…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Will the Ram Gooseneck to 5th Wheel Trailer Coupler Adapter Inner Tube Work On a Semi

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching