Which Bearing Buddy Bra Will Fit a Bearing Buddy With a Overall Diameter of 2-1/8 Inches

Question

Question:

My bearing buddy OD is 2 1/8 inch. Will the BB19B fit?

asked by: Carey D

0

Expert Reply:

Yes, the Replacement Bearing Buddy Bras, part # BB19B, you have referenced, will fit the Bearing Buddy bearing protectors that measure 2.125 (2-1/8 inches) in overall diameter.

expert reply by: Jeff D

0

Answer 1

Hey Robert, it sounds like you're looking for the Kodiak XL ProLube Oil Bath Hub Body and Cap #xlprolube1980. This oil bath cap is designed for 3.5k axles, and includes the hub, cap, seals, and necessary bearing lube. If there is something else I…

view full answer...

Answer 2

You actually don't have to use a thread sealant with the Bearing Buddies like the part #BB2080T-SS like what you mentioned.

view full answer...

Answer 3

The two special trailer tires we offer in your 4.80/4.00-8 size are both bias ply types, Load Range B tire #AM10002 and Load Range C tire #AM10004. The tire/wheel item you referenced, part #AM30050, includes this C-rated tire on a galvanized 4-on-4…

view full answer...

Answer 4

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 5

You're on the right track! If you're wanting to install a new 4 way connector on your snowmobile trailer you can use the 35-ft 4 way Trailer Wiring Harness #A35W42B. This is a wishbone style harness that comes with the tail light wiring…

view full answer...

Answer 6

The most likely cause for the turn signals not to work when the running lights are on with your trailer is a bad or weak ground. It's very possible that a weak ground connection can be just strong enough to allow sufficient current for some…

view full answer...

Answer 7

Do not despair. I will be happy to help. This does sound like a classic ground issue but there could be some other factors involved as well. So we will start with the easy things to check and work our way from there. Testing the trailer connector on…

view full answer...

Answer 8

Actually all you really have to do is remove the oil from the hub and then pack the hubs with grease and then get the correct bearing buddy to match the threaded hub bore. You will need to measure the inner diameter of where the old grease cap…

view full answer...

Answer 9

The base for Yates bow stop #YR6Y33-4 measures 3 inches by 2-7/8 inches. I have included a picture showing the measurements for you. Bow stop #YR4Y22-3 has a base that is 2 inches by 2 inches and a 4 inch span. That might work for you since the…

view full answer...

Answer 10

In order to give you an exact torque specification for your trailer wheels, I would need to know the stud size in addition to the diameter that you provided. For example, the most popular 8" diameter wheel we sell with a 4 on 4" lug pattern…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Which Bearing Buddy Bra Will Fit a Bearing Buddy With a Overall Diameter of 2-1/8 Inches

Product Page this Question was Asked From

Continue Researching