Are There Replacement Caps for the Kodiak XL ProLube Oil Bath Hub Body and Cap

Question

Question:

I am searching for the screw in caps for the Kodiak XLPROLUBE1980, I am needing the caps only, are they available or do I need to purchase the entire kit?

asked by: Todd G

0

Expert Reply:

If you have the Kodiak XL ProLube Oil Bath Hub Body and Cap part # xlprolube1980 you'll need to purchase the complete unit as the oil caps are not available separately.

expert reply by: Conner L

0

Answer 1

Hey Bob, thanks for reaching out. That's a great question, and it's a common point of confusion. The Hub Saver #HS79FR is not designed to keep the hub on the spindle if the castle nut backs off or falls off. The castle nut, washer, and cotter…

view full answer...

Answer 2

Jason, you only need one Hub Saver per wheel. Since they're sold in a pack of two, one package is enough for a single-axle trailer with two hubs. If you have a tandem-axle trailer, you'll need two packs to cover all four wheels. The Hub Saver…

view full answer...

Answer 3

That’s a great question, Jorge - this one can definitely be a little tricky the first time you run into it. On the Dexter/Titan Model 6 actuator like yours, resetting the breakaway lever isn't to difficult. To reset it, you’ll first want to…

view full answer...

Answer 4

Hey Tom, great question! Both products provide an easy way to measure tongue weight, but they excel in different situations. The BTBRV Trailer Jack Foot Scale #BTBRV014 measures tongue weight at the trailer jack, so you don't need to position a…

view full answer...

Answer 5

I do have a solution, but we do not have replacement parts for a Tie Down Engineering LP75 brake actuator. What I can offer is a replacement actuator with the same capacity that takes a 2" ball like your LP75. I recommend the Dexter DX7.5…

view full answer...

Answer 6

Hello Chris, Yes, it would be quite difficult to find a replacement master cylinder for your Dexter model LP75. The brake actuator was actually a Tie Down Engineering part that Dexter took over as Tie Down Engineering is no longer in business but…

view full answer...

Answer 7

Hi Chris! I am not 100% sure why you have two lines going to each brake, but I think that was to daisy chain them together. This was supposed to make bleeding the brakes easier, but I'm not sure if it really did much or not. The Kodiak #KOD59FR…

view full answer...

Answer 8

We can get you a replacement for your TDE LP75 disc brake actuator; that's a 7,500 lb actuator that accepts a 2" hitch ball, and the correct option will depend on if your trailer tongue is 3" wide x 4" tall or 3" wide x…

view full answer...

Answer 9

Yes, the correct Replacement Bleed Port for Kodiak 225 Disc Brake Calipers, like #KDBC225DAC is part #KBPBB, which has the correct 1/4"-28 bleed screw and 1/8" adapter fitting. Just in case, the correct replacement silicone dust boot is…

view full answer...

Answer 10

When you bleed the brakes on your trailer after installing the Kodiak Calipers #KDBC225DAC, you will want to start with the brake that is furthest away from the actuator. Of the two bleeder valves, you will want to use the bleeder valve that is on…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Are There Replacement Caps for the Kodiak XL ProLube Oil Bath Hub Body and Cap

Product Page this Question was Asked From

Continue Researching