Correct Replacement Bleeder Valve for Kodiak DBC-225 Disc Brake Calipers

Question

Question:

Is Item # KBPBB the correct bleeder valve for the Kodiak DBC-225 caliber? Thank you.

asked by: Mike

0

Expert Reply:

Yes, the correct Replacement Bleed Port for Kodiak 225 Disc Brake Calipers, like # KDBC225DAC is part # KBPBB, which has the correct 1/4"-28 bleed screw and 1/8" adapter fitting.

Just in case, the correct replacement silicone dust boot is part # K225BSSI and the replacement adapter port is part # K22590A.

expert reply by: Carla M

0

Answer 1

When you bleed the brakes on your trailer after installing the Kodiak Calipers #KDBC225DAC, you will want to start with the brake that is furthest away from the actuator. Of the two bleeder valves, you will want to use the bleeder valve that is on…

view full answer...

Answer 2

When it comes to finding the correct replacement hub for your trailer axle, we first would need to know what the current inner and outer bearing number is on your axle. There should be a stamped number on both the inner and the outer bearing. If you…

view full answer...

Answer 3

To check the pins on the vehicle side 7-Way, you can use a circuit tester or the volt meter. The circuit tester will show you if a signal is coming through on the pin you are testing while the volt meter will tell you that and how much voltage is…

view full answer...

Answer 4

There is not any melting that is done to keep the dust seals on, but they may have used an adhesive of some sort. Normally they are just a tight fit and a small flat head screwdriver can be used with a rubber mallet to remove it. Most of the time you…

view full answer...

Answer 5

I wish we had an install video or even a manual for the Kodiak Caliper Rebuild kit #KDBC225KIT that you referenced but the best we can offer at this time is an exploded diagram that shows how all of the parts go together.

view full answer...

Answer 6

While there is not a manual or video available for the Kodiak Disc Brake Caliper Rebuild Kit #KDBC225KIT I did find an expanded drawing of the parts of Kodiak Disc Brake Caliper #KDBC225S which should help so you can see how the pieces fit. The…

view full answer...

Answer 7

In my research I found that the grease seal you are looking for could have an inner diameter of either 2.24 or 2.12 inches and an outer diameter of 3.37 inches when measured with a digital caliper like #PTW80157. The closest thing we have to this is…

view full answer...

Answer 8

The GS2250DL and 22333TB grease seals are very similar but not the exact same, they have the same inner diameter of 2.250" but a different outer diameter. The outer diameter of the GS2250DL is 3.376" whereas the outer diameter of the…

view full answer...

Answer 9

I've actually answered a similar question on this before and found: In my research I found that the grease seal you are looking for could have an inner diameter of either 2.24 or 2.12 inches and an outer diameter of 3.37 inches when measured with…

view full answer...

Answer 10

The most likely place for brake fluid to be leaking out of your hydraulic brake system is at the fittings or master cylinder. To check the fittings, chock the trailer wheels and back up the trailer so that the brakes engage. With the actuator engaged…

view full answer...

Answer 11

The bleed screw of the Kodiak #KBPBB is the size 1/4"-28 and the thread size for the sleeve adapter it screws into is 1/8 inch.

view full answer...

Answer 12

So on the replacement bleed port #KBPBB with a 1/4 inch -28 screw and 1/8 inch adapter. But I am not sure how you would use it as a tee. Adapter port #K22590A has 1/8" NPT and 3/16" FIF threads and might be a better option depending on the…

view full answer...

Correct Replacement Bleeder Valve for Kodiak DBC-225 Disc Brake Calipers

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching