Where do I find the Model Number of my Roof Vent

Question

Question:

Hi, I have a Middlebury cargo trailer, model MTTCH 8.5x20TA3, with a crank up vent that the cover needs replaced. It looks like the Ventilator dome cover on your website. Where would I find the brand and model on my vent to be sure.

asked by: Tony

0

Expert Reply:

The model and serial number of your vent will be marked with a sticker or stamped on the upper side. Basically open the vent and look down in from the top. It may also be located on the bottom and visible when the screen is removed.

If this is not present use the MaxxAir UniMaxx Universal Replacement Lid for RV and Trailer Roof Vent part # MA00-335001 that is made as a universal fit for all of the standard 14"x14" roof vents

expert reply by: Randy B

0

Answer 1

Most likely we have what you are looking for but you will need to first determine what vent you have on your trailer. In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly…

view full answer...

Answer 2

You did indeed see a video showing how to replace the vent lid #BVD0449-A01. I have linked that video for you here as well. IT was one that I made a while back and that is probably where you saw it.

view full answer...

Answer 3

To remove the damaged vent cover, remove the connection to the actuating strut, so the cover can tilt all the way upwards. To do this, you will need to remove the interior screen, the knob and the interior trim piece. Then, remove the two screws that…

view full answer...

Answer 4

I tried looking up what vents came on your 2011 Coachmen Chaparral 268RLE but unfortunately it doesn't look like Coachmen kept a record of that. If you can let me know what brand you have I can see if we have a replacement screen for it as these…

view full answer...

Answer 5

In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly 14-1/4" x 14-1/4" and have roof vents that measure 14" x 14". To pick the correct cover, you will also…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Where do I find the Model Number of my Roof Vent

Product Page this Question was Asked From

Continue Researching